Johnson Controls n30 point mapping

Technical Bulletin Date 9 2006 12 2005 Supervisory Controller Point Mapping Supervisory Controller Point Mapping 3 3 Concepts 4 Database 4 Generation 4 Databases for Networked N30s 4 Mapping to an N30 4 Builder 5 Documents 5 Printouts 6 Application Specific Controllers ASCs 7 Overview 8 Procedures 10 Configuration Printouts 10 LCP DC9100 and DX 9100 Configuration Printouts 12 Controllers to an N30 Database with Project Builder 14 Controllers to the N30 Database with a VT100 15 Controller Points to N30 Objects with Project Builder 17 Controller Points to N30 Objects with a VT100 18 Mapping Tables 21 Handling Unit AHU 22 UNT Controller 23 Air Volume VAV Controller 23 Controller Modular Assembly VMA 1400 Series 24 Interface Module PHX 24 Integrator Unit 25 2006 Johnson Controls Inc Code No LIT 6891400 Vendor Device VND 25 Lighting Controller ILC 26 Fire Controller IFC 27 Terminal Controller 28 and Central Plant Controller Digital Controller LCP DC9100 31 Extended Digital Controller 35 Module XTM and XT 60 64 65 Supervisory Controller Point Mapping Supervisory Controller Point N30 Supervisory Controller referred to as N30 throughout this provides supervisory functions to intelligent controllers controllers have a number of points and internal parameters are used to store input data and control hardware for example sensors and fan controls This document assumes that are manually entering points using a VT100 Terminal or Terminal Emulator This document contains considerations when mapping points in an N30 database where to get configuration printouts for controllers document also describes how to configuration printouts for Air Handling Unit AHU UNT Controller Variable Air Volume VAV Controller Interface Module PHX and TC 9100 controllers Lab and Central Plant Controller LCP DC9100 and configuration printouts add controllers to an N30 database with Project Builder add controllers to an N30 database with a VT100 map controller points to N30 objects with Project Builder map controller points to N30 objects with a VT100 document also contains point mapping tables to map controller to the N30 database Unless otherwise indicated the information in this document applies to the N31 Supervisory Controller Concepts Database Generation Databases for Networked N30s Mapping to an N30 where the N30 system is defined Contains information about points alarms etc generation in an N30 consists of setting up the site and then and adding controllers and objects such as schedules energy objects and operators up an N30 network database is similar to the procedures used set up a standalone N30 database The main differences are the of defining a copy holder device and a BACnet Broadcast Device BBMD object when it is necessary to across network segments objects should be defined only when they are to communicate across network segments limits described in this document apply regardless of the points are mapped into the N30 N30 maps controller point data to objects in the N30 so that points the controller are identified with objects in the N30 This allows an to read and write to the points in the controller cannot use all the points in the controller Of the points that can used only some are commandable In the point mapping tables in document the Command Allowed column indicates which points N30 commandable N30s can read the values of non commandable but cannot issue commands override or adjust these points can both read and control commandable points you map controller points to the N30 it is very important that consider which controller points are non commandable Map controller points to N30 objects that you do not controlled by the N30 Conversely map commandable controller to N30 objects that you want the N30 to control Supervisory Controller Point Mapping Builder Builder defines the N30 Supervisory Controller database by mapping points from field devices to N30 objects and other N30 objects such as schedules and calendars Project allows downloads and uploads to any N30 in the network and N2 controllers that are attached to N30s Project Builder defines and N2 Controller objects imports predefined N2 controller files from Configuration Tools and Advanced Management AIM Point Schedules to map the input and points to the N30 and adds and edits objects in the project to Table 1 for documents related to N30 point mapping To Builder User Guide LIT 693205 Supervisory Controller Quick Start Technical Bulletin Documents 1 Related Documents Information About Project Builder and M View up an N30 System Printouts map controller points to an N30 you need to know the point type address of the points in the controller Table 2 lists where you can this information for different types of controllers and where you find instructions on how to generate the controller printouts 2 Controller Configuration Printouts Type Printed From Tools PRO Located PRO User Guide Handling Unit AHU UNT Controller Air Volume VAV 1400 Series Modular VMA1400 Interface Controller TC 9100 and Central Plant LCP DC9100 PRO User Manual