Johnson Controls NU-NCM300-tb

Technical Bulletin Date 5 2003 Control Module 300 Series Control Module 300 Series 3 3 Concepts 7 7 Bus Cards 10 Considerations 17 Considerations 19 Cable Guidelines 29 Setup 44 the N2 End of Line Switches 48 the Memory Switches 49 for Windows Operating System WNCSETUP 49 Idle Time 52 and Order Codes 53 Procedures 55 an NCM401 with an NCM300 55 56 the NCM 56 56 Commissioning Problems 63 Haul Modems Line Drivers 66 Power Up LEDs 67 Module Field Checks 71 Troubleshooting 72 A Fire Net NCM 74 2003 Johnson Controls Inc No LIT 6360251 Release 12.00 Control Module 300 Series Technical Bulletin Documentation 74 Configuration 75 Boards 77 81 81 a Fire Net NCM 86 Messages 86 Numbers 87 B NCM Maintenance 88 88 Maintenance Flowcharts 88 Quick Check 92 Inspection 92 Inspection 92 C NCM100 Power Supply Troubleshooting 105 105 Affected 105 Action 105 Action 106 Control Module 300 Series Technical Bulletin Control Module 300 Network Control Module 300 Series NCM300 is the main module in the Metasys Network Fully programmable NCM coordinates and supervises the control activities for all and control loops connected to it via Network Expansion Units and Application Specific Controllers ASCs Table 1 shows models available for the NCM300 Series document also shows how to replace an NCM401 with an Control Module 300 Series Technical Bulletin 1 NCM300 Series NCMs not attempt to upgrade NU NCM300 1s at Rev A hardware or any 1 The NCM300 is connected to the Metasys network via the ARCNET Local Area Network LAN The NCM311 is the European version of the NCM300 Construction operation are similar to the NCM300 however there are minor modifications that required to conform with European Safety and Emission standards that apply in all Union countries The NCM350 is functionally the same as the NCM300 however it connect to either an ARCNET or Ethernet LAN can upgrade from an NCM300 either by swapping the NU NCM300 0 for an or by upgrading an NU NCM300 1 at Rev B or later using the to NU NCM350 1 Upgrade Kit NU ROM150 Instructions come with upgrade kit of NU NCM300 0s to NCM350s If you have already tried to upgrade one of models choose one of the following options the ROM SIMM with an NU ROM101 The NCM is now an NCM300 suitable ARCNET applications only the NCM to the repair center for upgrade to NU NCM350 1 Go to the Products tab and click on Repair Center NCM3n0Upgrade on The Advisor for details physical difference between the NCM300 and the NCM350 is a Flash chip in of the ROM chip This Flash chip contains everything that is in the ROM along configuration data The Flash chip also contains information about the ISA drivers the user can download additional information to the Flash chip version of the NCM350 Contains 8 MB total memory Replaces all previous of NCM300s and NCM350s Meets UL 864 UUKL for smoke control The NCM361 is the European version of the NCM350 You can the NCM361 new or you can upgrade an NCM311 either by swapping the for an NCM361 or by upgrading the NU NCM311 1 using the to NU NCM361 1 Upgrade Kit NU ROM150 Instructions come with upgrade kit and operation are the same as the NCM350 however there are minor that are required to conform with European Safety and Emission that apply in all European Union countries version of the NCM361 Contains 8 MB total memory Replaces all previous of NCM311s and NCM361s The Fire Net NCM is connected to the Intelligent Fire Network It is physically the same as the NCM300 however it UL 864 UOJZ Listed for fire alarm use The NCM300 FIRE comes with a ARCNET board 2 MB additional memory and a special power supply NU NCMFIRE 1 is the same as the NU NCM300 FIRE except that it has 8 MB of For information on the Fire Net NCM refer to the Metasys Intelligent Fire Technical Bulletin LIT 448196 replaced by NU NCM350 8 The Smoke Control NCM is physically to the NCM300 however it is UL 864 UUKL Listed For information on the Control NCM refer to the Smoke Control Technical Bulletin LIT 636330 NCM Control NCM Control Module 300 Series Technical Bulletin otherwise specified the inform