Kidde 3101082-EN R006 FX-2WIRE Analog Class A-B Two-Wire Module Installation Sheet

1 Slide switch Analog Class A B Module Installation operation module provides a bicolor LED that shows its status Green LED flashes Red LED flashes FX 2WIRE module is designed to interface between compatible two wire smoke detectors and a control panel It monitors circuit and smoke detectors and signals the control panel of any or alarm conditions The module also regulates and supervises 24 VDC input power module is configured from the factory to operate as a two wire device that does not require alarm verification It can be for two wire alarm verified operation through front panel or the configuration utility When using the alarm feature of the control panel do not mix normally open initiating devices with two wire conventional smoke detectors module recognizes the CleanMe signal from detectors that this feature module device address is set using the two rotary switches on the front of the module One device address is required device can be set for Class B or Class A operation using the slide located on the front of the module This module cannot be used on a device loop with isolator or isolator bases switch operation following slide switch settings determine the operation of the Setting the initial slide switch position is generally performed module installation This setting can be changed while the is operating but the change must be confirmed through front programming or using the configuration utility 1 Slide switch operation Operation Device type description 1 B B 2 wire smoke non verified the module to monitor two wire smoke detectors that do not alarm verification and normally contact initiating devices on a Class B A 2 wire smoke non verified the module to monitor two wire smoke detectors that do not alarm verification and normally contact initiating devices on a Class A used A Additional device types are available through front panel or the configuration utility Refer to applicable control technical reference manual and wire this device in accordance with applicable national and codes ordinances and regulations This module will not operate without electrical power As frequently cause power interruption you should discuss further with your local fire protection specialist The module is shipped from the factory as an assembled unit it no user serviceable parts and should not be disassembled install the module Verify that all field wiring is free of opens shorts and ground Make all wiring connections as shown in and in Figure 4 Set the module address Refer to the panel technical reference for a list of valid addresses a screwdriver to adjust the two rotary switches on the front of module Set the TENS rotary switch 0 through 12 for the 10s 100s digit and the ONES rotary switch for the 0 through 9 For example device address 21 set TENS rotary switch to 2 set the ONES rotary switch to 1 see Figure 2 Set slide switch P1 to appropriate setting Refer to Mount the module on the electrical box using screws provided with Mount the wall plate on the module using the hardware shown in electrical box 3 2 Module address 6 7 0 Insert screwdriver here 2020 Carrier 2 3101082 EN REV 006 ISS 20OCT20 3 Module installation to 28.3 VDC line voltage Maximum 20.6 V peak to peak panel input power resettable power current detector current compatibility ID fault impedance environment humidity mA mA mA k to 120 0 to 49 to 93 noncondensing at 32 to 140 to 60 American 4 inch square in 64 mm deep 2 gang box 4 in square box 1 1 2 in mm deep 14 16 or 18 AWG wire 1.5 1.0 or 0.75 mm2 Sizes 16 18 AWG are preferred k P N EOL 4.7 25 per wire temperature range electrical boxes size resistor value device circuit IDC Max circuit resistance Max circuit capacitance Cover plate plastite screws 2X Wall plate Screw Module Compatible electrical box the device as shown in Figure 4 Be sure to observe the polarity the wires to the control panel technical reference manual for wiring 4 Module wiring From control panel non resettable Class B Detector power To next device From previous device Class A or Class B Class A information contact information see www kidde esfire com Maximum 25 resistance per wire Maximum 12 AWG wire minimum 18 AWG wire Maximum 23.8 VDC at 35 mA 4.7 k EOLR used for Class B only Typical initiating device Class B 2 3101082 EN REV 006 ISS 20OCT20