Kidde 3102000-EN R002 Genesis WG4 Outdoor Horn-Strobe Installation Sheet

WG4 Outdoor Horn Installation Sheet Genesis WG4 Outdoor Horn Strobe is a life safety notification designed for indoor or outdoor use on ceilings or on walls Table 1 for a list of models and Table 2 for a list of accessories surface mount applications mount the WG4 onto a Model 449 box using the gasket shipped with the appliance For flush applications where the mounting surface is flush with the of the wall or ceiling use the WG4GSKT gasket kit that you need a Model 449 electrical box for waterproof or a standard mount 4 in square box for all other horn strobe includes field configurable jumper options that allow to set the strobe pattern to temporal or continuous the horn to temporal or continuous and the horn volume to low or high horn strobe also includes a field configurable switch for setting the candela level This setting is locked in place and is visible after installation 1 Models rated wall ceiling horn strobe white with marking clear lens rated wall ceiling horn strobe white marking clear lens rated wall ceiling horn strobe red with marking clear lens rated wall ceiling horn strobe red marking clear lens 2 Accessories 1 Outdoor rated surface skirt white for Genesis WG4 1 or horn strobe surface skirt red for Genesis WG4 or horn strobe 2 Appliance replacement gasket flush mount The trim skirt is outdoor rated when used with the Model 449 box Not compatible with the trim skirts synchronize horn strobe operation you must install a separate source See Table 3 When connecting the horn to a listed control panel verify synchronization operation on the list for the corresponding panel output module 3 Compatible synchronization source models Represents any number of additional characters signal master mount or auxiliary power this device in accordance with applicable requirements and in with the local authorities having jurisdiction Electrocution hazard To avoid personal injury or death electrocution remove all sources of power and allow stored to discharge before installing or removing equipment Electrical supervision requires that you break the wire run at each Do not loop wires around the terminals You can mount the WG4 horizontally or vertically on either the wall ceiling place the electrical box accordingly See Figure 1 When using a 449 electrical box discard the gasket that is shipped When using a trim skirt or a surface mount application use the that comes with the WG4 unit the box or flush mount applications on a flat surface use the WG4GSKT accessory install the horn strobe Remove the cover from the horn strobe by first removing the six screws See Figure 2 item 1 2018 United Technologies Corporation 4 3102000 EN REV 002 ISS 16MAR18 Position the appropriate gasket over the backplate ensuring that 2 Exploded view of the assembly wire slot and other holes line up properly the protective backing from the gasket surface and apply the gasket to the WG4 with the adhesive side the appliance the gasket firmly against the back surface of the appliance that the gasket seats properly Place the optional trim skirt over the electrical box if desired See 2 items 4 5 and 6 Also see on page 3 for list of compatible boxes Feed the field wiring through the wire slots on the gasket and the See Figure 2 item 3 and Figure 3 item 1 Align the appliance and trim skirt if applicable and then secure backplate to the electrical box with the supplied screws the assembly to ensure that it is securely mounted Set the candela output default candela setting is D To select a different candela align the S2 indicator to the desired candela output See 3 item 6 For candela output ratings see Table 8 Table 9 Table 10 Set the strobe pattern default strobe pattern setting is continuous To use the strobe private mode which is not ULC listed cut jumper See Figure 3 item 4 Set the horn volume default horn volume setting is high To set the horn to low cut jumper JP3 See Figure 3 item 2 default horn pattern is temporal To use a continuous horn cut jumper JP1 See Figure 3 item 5 Connect the signal circuit field wiring to the appropriate terminals that both the horn and the strobe are powered from the NAC must observe polarity for the unit to function properly See on page 3 Remove the strobe protective cover shown in Figure 3 item 3 Do not touch the glass of the strobe tube underneath as this shorten the life of the glass tube Position the cover over the backplate and then secure it with the cover screws Test the unit for proper operation 1 Horn strobe mounting positions Set the horn pattern Cover screws 6X Front cover Backplate Optional trim skirt WG4 gasket Electrical box 3 Jumper switch and protective cap locations Wire slot JP3 horn volume jumper Protective cap JP4 strobe pattern jumper JP1 horn pattern jumper S2 candela setting switch 4 3102000 EN REV 002 ISS 16MAR18 Figure 4 Connect all wiring in accordance with national electrical and applicable local requirements Equipment hazard To avoid equipment damage ensure that signal voltage does not exceed the voltage rating of the device 4 Wiring diagram Horn strobe IN Horn strobe IN Marking indicates the signal polarity to activate the device Horn strobe OUT Horn strobe OUT Not used 5 UL 1971 minimum light output of rating vs angle 10 15 20 Angle Percentage of rated output Horizontal plot not change the factory finish a visual inspection and an operational test twice a year or as by the local authority having jurisdiction unit is not serviceable or repairable Should the unit fail to contact the supplier for replacement voltage W H D level output tone operating current output size electrical box Outdoor environment humidity VDC 24 VFWR nominal 8.5 1.4 in 142 216 36 mm Table 4 Table 5 Table 6 and 7 kHz Table 11 Table 8 Table 9 Table 10 and 5 to 18 AWG 0.75 to 2.50 mm 449 in square by 1.5 in deep box to 151 to 66 to 95 noncondensing 4 Sound level output dBA per UL 464 Setting High Low High Low Decibels A weighted 464 Sound level output measured in a reverberant room at 10 ft m 5 Sound level output dBA per CAN ULC S525 setting High Low High Low Decibels A weighted Sound level output measured in an anechoic room at 3.05m 6 Directional sound characteristics horizontal pattern per