Kidde 3102529-EN R001 KIR-HD Intelligent Fixed-Temperature Heat Detector Installation Sheet
File Preview
Click below to download for free
Click below to download for free
File Data
Name | kidde-3102529-en-r001-kir-hd-intelligent-fixed-temperature-heat-detector-installation-sheet-8106745329.pdf |
---|---|
Type | |
Size | 733.54 KB |
Downloads |
Text Preview
and wire this device in accordance with applicable national and codes ordinances and regulations Intelligent Fixed and Rate of Rise Detector Installation studies indicate that heat detectors should only be when property protection alone is involved Never rely on detectors as the sole means of fire protection To ensure proper operation store the detector within the ranges Allow the detector to stabilize to room before applying power The dust cover supplied must remain on the detector during and be removed prior to commissioning and service dust cover is not a substitute for removing the detector during construction or heavy remodeling This detector does not operate without electrical power As fires cause power interruption discuss further safeguards the local fire protection specialist This detector does not sense fires in areas where heat cannot the detector Heat from fires in walls roofs or on the side of closed doors may not reach the detector This detector by itself does not provide smoke or fire protection this detector with ionization or photoelectric smoke detectors both This detector does not detect oxygen levels smoke toxic gases flames Use this device as part of a broad based life safety which includes a variety of information sources pertaining heat and smoke levels extinguishment systems visible and devices and other safety measures Canada install according to CAN ULC S524 Standard for the of Fire Alarm Systems CSA C22.1 Canadian Electrical Part 1 and the local authority having jurisdiction and wire the base as described on the installation sheet with the base Set the detector address Refer to the panel technical reference for a list of valid addresses Use a screwdriver to adjust two rotary switches on the back of the detector Figure 2 Set the left rotary switch 0 through 12 for the 10s 100s digit and the right rotary switch for the 0 through 9 digit Attach the detector to the base by rotating the detector clockwise it snaps into the locked position 2 Setting detector address address 52 shown Insert a screwdriver here to set the address model KIR HD Intelligent Fixed Temperature and Rate of Rise Detector that contains a fixed temperature heat sensor to detect from fire The heat sensor monitors the temperature of the air in surroundings and the detector analyzes the data to determine to initiate an alarm indicator The LED indicator see Figure 1 displays the following Normal Green LED indicator flashes no action Alarm active Red LED indicator flashes evacuate the area 1 KIR HD features install the detector Self locking tab LED indicator 2017 United Technologies Corporation 2 3102529 EN REV 001 ISS 15AUG17 testing notify the proper authorities that the fire alarm system is maintenance and will be temporarily out of service each sensor in the detector Heat damage Excessive heat may damage the detector cover Do not apply excessive heat when using a hair dryer using a Testifire detector tester you must install a Testifire Assembly sure the Testifire Adapter Assembly model is installed in the Testifire detector tester before Refer to the Testifire Adapter Assembly Installation Sheet 3101942 ML for further details perform an initial installation test Remove the detector from its base and verify that the proper address trouble signals and messages are reported wired for Class A operation verify that the detector continues to first with SLC IN disconnected reconnect SLC IN and with SLC OUT disconnected Refer to the installation sheet the base Place a momentary ground fault on the SLC to verify operation of ground fault detection circuitry Run a system detector maintenance report on all detectors and that the readings fall within acceptable limits perform a function test desired use the fire alarm control panel to put the detector or into a service group for testing Refer to the panel technical manual for instructions Activate the heat sensor using a hair dryer maintaining a distance three inches or using a Testifire detector tester per the instructions ensure proper operation plan maintenance in accordance with the of the authority having jurisdiction Refer to Standard for the Inspection and Testing of Fire Alarm and NFPA 72 National Fire Alarm and Signaling Code to application bulletin P N 3102534 EN for additional information cleaning instructions voltage operating level to 19.95 VDC to 35 Hz with an amplitude of in spacing ft 15.2 m centers bases KI SB4 KI RB4 KI IB4 KI ABDT KI ABLT detector testers 1 Testifire 2000 environment humidity to 100 0 to 38 to 93 noncondensing temperature to 140 to 60 1 Requires the SIGA2 TSTSPACER Testifire adapter assembly information American and ULC fixed alarm rating compliance UL 521 57.2 device complies with part 15 of the FCC Operation is subject to the following two 1 This device may not cause harmful and 2 this device must accept any received including interference that cause undesired operation Canada Class A digital apparatus complies with ICES 003 information contact information see www kiddelifesafety com Perform a sensor function test as described below alarm point to 141 53.9 to 60.6 2 3102529 EN REV 001 ISS 15AUG17