Kidde 3102687-EN R001 G4SE Genesis LED Strobe Expander Installation Sheet

Genesis LED Strobe Installation Sheet and wire this device in accordance with applicable national and codes ordinances and regulations Electrical supervision requires that you break the wire run at terminal Do not loop the notification circuit field wires around the new flush mount installations install the electrical box so the is at least 83 inches above the finished floor See Figure 1 install the G4SE strobe expander Attach the G4SE strobe expander to a standard metal electrical Use the screws provided with the electrical box Tighten until with the mounting surface Run the field wires through the stobe expander opening and then them to the terminal screws See Figure 2 and Figure 3 Remove the shorting clip and then install the notification appliance to the notification appliance installation sheet for 1 Typical flush mount installation Electrical box Strobe expander Sheet metal screws 2X with electrical box Notification appliance Shorting clip Genesis LED Strobe Expanders add a second synchronizable strobe to Genesis LED G4 horn strobes and Genesis G4S speaker strobes Together they provide fire alarm signaling mass notification emergency communication signaling in one assembly Synchronized operation requires a separately installed device See the control unit or power supply list for compatible synchronization devices document provides installation instructions for the G4SE strobe models listed in Table 1 below 1 Models expander white amber lens expander white red lens expander white green lens expander white blue lens expander white no marking amber lens expander white no marking red lens expander white no marking green lens expander white no marking blue lens expander red amber lens the G4SE as shown in Figure 2 and Figure 3 To maintain circuit continuity do not remove the shorting clip you are ready to install the notification appliance in cm 2020 Carrier 3 3102687 EN REV 001 ISS 27AUG20 2 G4SE strobe circuit wiring Notification appliance strobe circuit in signal polarity shown in the Expander strobe circuit in signal polarity shown in the active condition Expander strobe circuit out Notification appliance strobe circuit out Shorting clip 3 G4SE speaker circuit wiring voltage current to 33 VDC to 33 VFWR output lens A models Green lens G models flash rate distribution lens B models lens R models Machine screws screws screws size torque Mounting screws to box center offset electrical boxes to 33 VDC 16 to 33 VFWR mA mA cd cd cd cd fps flash per second approx Figure 4 max between any two devices determine allowed wire resistance to these specifications and the for the synchronized source to 18 AWG 0.75 to 2.50 mm2 lbf in 0.6 N m typical lbf in 1.8 N m typical lbf in 1.4 N m max Figure 5 in 9.9 cm American 4 inch square box inches deep no extension ring to 122 0 to 50 to 93 noncondensing to 158 40 to 70 environment humidity temperature This device was tested to the regulated 24 VDC FWR operating limits of 16 V and 33 V 4 75 cd light distribution Speaker circuit in shields if used must be continuous and free earth ground except at the signal source Speaker circuit out Shorting clip and testing unit is not serviceable or repairable Should the unit fail to contact the supplier for replacement a visual inspection and operational testing upon completion of and annually thereafter or as directed by the local authority jurisdiction 3 3102687 EN REV 001 ISS 27AUG20 Horizontal left Horizontal right Vertical bottom Measured UL minimum 5 Dimensions 8.0 in 20.32 cm 2.33 in 5.92 cm 5.12 in 13.0 cm information rating compliance Canada 24 DC and 24 FWR device complies with part 15 of the FCC Operation is subject to the following two 1 This device may not cause harmful and 2 this device must accept any received including interference that cause undesired operation Class A digital apparatus complies with ICES 003 dry information contact information see www edwardsfiresafety com 3102687 EN REV 001 ISS 27AUG20 3