Kidde K85001-0441 -- Bell-Strobe Plate

Bell Strobe Plate Series Series c w 439 6 inch Bell ordered separately Series Bell Strobe Plates are specially designed for use with life safety communication and control equipment alert the hearing impaired of a life safety event Strobes are with 15 cd 15 75 cd 30 cd and 110 cd effective flash They are fully compatible with Genesis signals part of the Enhanced Integrity line of products 403 series exceed UL synchronization requirements within 10 other over a two hour period when used with a EG1M Signal Master or GSA CC1S Synchro Module flash from 403 series strobes can be noticed from almost any in the room corridor or large open space Light disper is controlled with a specially shaped reflector that directs a of 12 per cent of rated light output above and below the and a minimum of 25 per cent of rated light straight out sides Series strobes are designed for 16 to 33 Vdc operation and be connected to signal circuits that output a constant not voltage A diode is used to allow full signal circuit supervi and polarized connections are made to 7 175 mm wire rugged steel plate with smooth bevelled edges is finished in a high quality baked red epoxy polyester powder coat Features Converts 439 model bells for renovation work easily adapts to existing or new bells conversion into Bell Strobes Mounts to North American two gang octagon and 4 inch square boxes UL 1971 listed synchronizing strobe Series strobes synchronize to the latest UL 1971 require when used with an external control source Genesis compatible Genesis and Integrity strobes on the same circuit meet UL synchronization requirements when used with an external module Approved for public and private mode applications 1971 listed as signaling devices for the hearing impaired UL 1638 listed as protective visual signaling appliances Rugged steel plate CRS plate with durable baked red epoxy polyester finish Field changeable field markings language or standard marking is easily changed optional LKW series lens kits 1 of 6 D A T A S H E E T K85001 0441 to be used for installation purposes Issue 1.1 Catalog u Strobes Horns Bells Chimes03 31 20Technology that saves livesfirealarmresources com The installation of visible and audible signals are subject to national and local standards codes and ordinances your Authority Having Jurisdiction for device installation requirements application standards and minimum performance specifications sound pressure levels in each signaling zone for alarm alert signals are at least 15 dB above the average ambient sound or 5 dB above the maximum sound level having a duration at least 60 seconds whichever is greater measured 1500mm the floor The average ambient sound level is the RMS sound pressure measured over a 24 hour period strobes are UL 1971 listed for use indoors as wall mounted notification appliances for the hearing impaired Prevail codes require strobes to be used where ambient noise conditions specified levels where occupants use hearing protection in areas of public accommodation Consult with your Authority Jurisdiction for details part of the Enhanced Integrity line of products 403 Series exceed UL synchronization requirements within 10 mil other over a two hour period when used with a syn source Synchronization is important in order to avoid sensitivity strobes are fully compatible with Kidde Genesis Series The flash intensity of some visible signals may not be adequate alert or waken occupants in the protected area Research indicates the intensity of strobe needed to awaken 90 of sleeping persons is 100 cd Kidde recommends that strobes in sleeping rooms rated at at least 110 cd These devices will not operate without electrical power As frequently cause power interruptions further safeguards such as power supplies may be required Wiring SIGNAL CIRCUIT bell and strobe can be connected to the same signal circuit as shown if the is configured for continuous signal operation Electrical supervision requires wire run to be broken at each device not loop signal circuit field wires around the Bell Strobe units leads SIGNAL CIRCUITS bell and strobe can be connected to different signal circuits as shown The is designed to be used on circuits that output a constant voltage Do not con strobe to a coded or pulsating voltage Electrical supervision requires wire run to be broken at each device not loop signal circuit field wires around the Bell Strobe units leads 2 of 6 D A T A S H E E T K85001 0441 to be used for installation purposes Issue 1.1 and Mounting 403 series bell strobe plates install a variety of standard flush mounted electrical boxes This one gang two gang 3 1 2 inch 4 inch octagon and 4 inch square The must be installed along with Kidde 439 series 6 inch 150 mm 8 inch mm and 10 inch 250 mm bells or separately The strobe must be con to a signal circuit which outputs a not pulsed voltage the bell can connected to pulsed or continuous circuits recommends that these fire alarm always be installed in accord with the latest recognized edition of and local fire alarm codes mm Distribution Patterns 1971 WALL MOUNTED STROBE LIGHT OUTPUT mm mm mm mm with 6 Shown for purposes Ordered series Plate mm mm mm Mount Box cd 5A Series Strobes cd 7A Series Strobes cd 5A Series Strobes cd 7A Series Strobes cd 3A Series Strobes cd 4A Series Strobes cd 3A Series Strobes cd 8A Series Strobes cd 4A Series Strobes cd 8A Series Strobes Output e grees Output Output e grees e grees Output Output e grees e grees Output Output e grees e grees 20 30 20 10 20 30 100 100 Output Output Output e grees e grees e grees Output Output Output Output Output Output Output Output Output min min min min min min min min min Output