Kidde K85001-0657 -- Intelligent Multisensor Heat and CO Detector

Intelligent Heat CO Detector KI HCD detector brings advanced multisensing technology a practical design that increases efficiency saves installation cuts costs and extends life safety and property protection Continuous self diagnostics ensures reliability over long haul while environmental compensation helps reduce costs Features Some features described here may not be supported by control systems Check your control panel Installation and Guide for details Next Generation Detection Technology Integrates rate of rise heat sensing with carbon monoxide KI HCD provides the best of both worlds with multisensor life monitoring Rate of rise heat sensing technology provides identification of smoldering fires as well as fast flaming With the added element of CO monitoring this detector pulls duty continually monitoring the environment for signs of as well as its invisible yet deadly companion carbon mon all KI Series detectors the KI HCD gathers analog information its sensing elements and converts this data into digital sig To make an alarm decision the detector on board micro measures and analyzes the heat sensor readings and this information to historical data Digital filters remove patterns that are not typical of fires thus virtually eliminating alarms detector also analyzes heat sensor independently from the CO to determine whether to initiate a fire alarm a life safety CO or both Sensor Markings Provide Easy Testing Identification Uses existing wiring Automatic device mapping Up To 250 Total Addresses Per Loop Automatic environmental compensation Non volatile memory Electronic addressing Automatic day night sensitivity adjustment Bicolor green red status LED Standard relay fault isolator and audible mounting bases 1 of 4 A T A S H E E T K85001 0657 to be used for installation purposes Issue 1 Catalog Intelligent Initiating DevicesTechnology that saves livesfirealarmresources com detection KI HCD detector provides a 15 9 per minute rate of heat sensor for the detection of fast developing fires as well a 135 57 fixed temperature sensor for slow building fires heat sensors monitor the temperature of the air and deter whether a fire alarm should be initiated Detection CO detection such as that provided by the KI HCD is mandated with increasing frequency in all types of com applications but particularly in occupancies such as hotels houses dormitories day care facilities schools hospitals living facilities and nursing homes Known as the CO is odorless tasteless and colorless It claims nearly 500 and results in more than 15,000 hospital visits annually KI HCD CO sensor monitors the presence of CO particles the air and determines whether a life safety alarm should be Alarm levels are reached at 70 ppm when detected for 60 240 minutes 150 ppm for 10 to 50 minutes and 400 ppm for to 15 minutes Device Mapping The loop controller learns where device serial number address is installed relative to other de on the circuit The mapping feature provides supervision of each installed location to prevent a detector from being reinstalled cleaning etc in a different location from where it was originally Stable Communication On board intelligence means less needs to be sent between the detector and the loop Other than regular supervisory polling response the only needs to communicate with the loop controller when has something new to report mounting bases have wiring terminals that are acces from the after mounting the base to the electrical The bases mount to North American 1 gang boxes and to inch or 4 inch octagon boxes 1 inches 38 mm deep They mount to European BESA and 1 gang boxes with 60.3 mm centers The KI SB4 KI RB4 and KI IB4 mount to North 4 inch sq electrical boxes in addition to the above They include the GSA TS4 Trim Skirt which is used to the ears on the base The KI ABST mounts to a inch square box only Series detectors mount to American 1 gang boxes inch or 4 inch octagon and to 4 inch square elec boxes 1 1 2 inches 38 mm They mount to European and 1 gang boxes with 60.3 fixing centers See mounting installation and wiring for information tab Base Base Base Base LED Indicator LED GSA LED The remote LED connects to the KI SB KI SB4 Standard Base only It features a North American size plastic faceplate with a white finish and red alarm LED Trim Skirt Supplied with 4 inch bases it can also ordered separately to use with the other bases to help hide imperfections not covered by the smaller bases Bases KI Series sounder bases are designed for use localized or group alarm signaling is required KI ABDT bases provide sounder capability to the KI HCD used with a GSA T3T4 Temporal Pattern Generator to CO TC4 and Fire TC3 tone patterns KI ABLT bases provide 520 Hz low frequency sounder ca to the KI HCD when used with a GSA T3T4 Temporal Generator to separate CO TC4 and Fire TC3 tone The KI ABLT is suitable for applications requiring low audible tones Cautions This product is intended for use in indoor locations of dwelling It is not designed to comply with Occupational Safety and Administration OSHA commercial or industrial stan The detector indicates the presence of CO gas at the detector monoxide gas may be present in other areas Failure to properly install test and maintain a CO detector may it to fail potentially resulting in loss of life This detector does not operate without electrical power As fires cause power interruption discuss further safeguards the authority having jurisdiction AHJ Maintenance maintenance regular or selected for proper detector should be planned to meet the requirements of the Au Having Jurisdiction AHJ Refer to current NFPA 72 NFPA and ULC CAN ULC 536 standards Sensor Life CO sensor has a 10 year life from the date of manufacture or the control panel indicates a sensor end of life condition comes first When the sensor reaches its end of life the signals a TRBL ACT condition on the control Pressing the Details button on the control panel displays OF LIFE ACT providing verification that it is an end of life of the CO sensor This trouble remains active until the is replaced even if the panel is reset and reporting technology microprocessor in each detector provides additional benefits and History Log Automatic Device Mapping and Stable Communication and History Log Each KI Series detector con runs self checks to provide important maintenance informa The results of the self check are automatically updated and stored in the detector non volatile memory 2 of 4 A T A S H E E T K85001 0657 to be used for installation purposes Issue 1 Wiring detector mounting bases accept 18 AWG 0.75mm2 16 14 AWG 1.5mm2 and 12 AWG 2.5mm wire sizes 16 AWG 1.0mm2 and 18 AWG 0.75mm2 are preferred ease of installation Detector Base KI SB KI SB4 is the basic mounting base Kidde KI Series detectors GSA LED Remote LED is by this LED resistance wire not exceed Ohms Sounder Bases Fire Mode AB4G AB4G LF sounder bases Setting High for dB cuts DATA DATA Term Description 1 Not Used 2 DATA IN OUT 3 Not Used 4 DATA IN 4 Remote LED 5 Remote LED 6 Not Used 7 DATA OUT IN IN Signature Controller Previous Device OUT OUT Next Device Vdc in power supply previous base in KI Device Controller previous device Mode Fire jumper for plus CO