Kidde K85001-0661 -- Intelligent Heat Detector, Rotary-Addressed

Intelligent Heat KIR Series smoke detectors bring advanced sensing technol to a practical design that increases efficiency saves installa time cuts costs and extends property protection capabilities self diagnostics ensure reliability over the long haul the latest thermister technology makes these detectors ideal dependable heat detection is required KIR HD is an intelligent fixed temperature fire detector that also be programmed as a rate of rise detector The KIR HD the temperature of the surrounding air and analyzes the from the sensor to determine whether to initiate an alarm fixed temperature heat function detects fire when the air near the detector exceeds the alarm point When as a rate of rise heat detector the KIR HD quickly a fast flaming fire Features Some features described here may not be supported by control systems Check your control panel Installation and Guide for details Next generation heat sensing technology 135 57 fixed temperature alarm point Programmable 15 8.3 per minute rate of rise alarm Uses existing wiring Up to 250 total devices per loop Non volatile memory Convenient rotary addressing Bicolor green red status LED Standard relay fault isolator and audible mounting bases 50 foot 15.2 meter spacing 1 of 4 A T A S H E E T K85001 0661 to be used for installation purposes Issue 1.2 Catalog Intelligent Initiating DevicesTechnology that saves livesROTARY ADDRESSINGfirealarmresources com intelligent digital device provides a 135 57 fixed heat sensor for the detection of heat due to fire The sensor monitors the temperature of the air and determines an alarm should be initiated The FX HD also can be as a rate of rise heat detector to its advanced thermistor technology the KIR HD detec is ideal for sensing fast flaming fires and for applications where detection is inappropriate The KIR HD is capable of per comprehensive self diagnostics and storing the results It particularly well suited to areas such as laundries and industries fluctuations in ambient temperature is expected KIR HD is compatible with FX Series intelligent panels Series detector bases mount North American 1 gang boxes inch or 4 inch octagon and to 4 inch square elec boxes 1 1 2 inches 38 mm They mount to European and 1 gang boxes with 60.3 fixing centers See mounting installation and wiring for information tab Indicator and reporting technology microprocessor in each detector provides additional benefits Self diagnostics and History Log and Fast Stable Communica and History Log Each KIR Series detector runs self checks to provide important maintenance in The results of the self check are automatically updated permanently stored in the detector non volatile memory Stable Communication On board intelligence means less needs to be sent between the detector and the loop Other than regular supervisory polling response the only needs to communicate with the loop controller when has something new to report mounting bases have wiring terminals that are acces from the after mounting the base to the electrical The bases mount to North American 1 gang boxes and to inch or 4 inch octagon boxes 1 inches 38 mm deep They mount to European BESA and 1 gang boxes with 60.3 mm centers The KI SB4 KI RB4 and KI IB4 mount to North 4 inch sq electrical boxes in addition to the above They include the Trim Skirt which is used to cover the ears on the base The KI ABST mounts to a 4 inch box only Base Base Base Base LED LED The remote LED connects to the KI SB or KI SB4 Base only It features a North American size 1 gang faceplate with a white finish and red alarm LED Skirt Supplied with 4 inch bases it can also be ordered to use with the other bases to help hide surface imper not covered by the smaller bases Bases KIR Series sounder bases are designed for use localized or group alarm signaling is required KI ABST bases provide sounder capability to KIR Series to and smoke detectors KI ABLT bases provide 520 Hz low frequency sounder capa to KIR Series smoke and heat detectors The KI ABLT suitable for applications requiring low frequency audible Addressing is made easy through the rotary dials located on the of the detector head Use a screwdriver to adjust the TENS switch 0 through 12 to set the 10s digit and the ONES switch to set the digit 0 through 9 The control panel will any duplicate addresses 5 9 screwdriver here device address 21 set TENS rotary switch to 2 and set ONES rotary switch to 1 2 of 4 A T A S H E E T K85001 0661 to be used for installation purposes Issue 1.2 Wiring detector mounting bases accept 18 AWG 0.75mm2 16 14 AWG 1.5mm2 and 12 AWG 2.5mm wire sizes 16 AWG 1.0mm2 and 18 AWG 0.75mm2 are preferred ease of installation Detector Base KI SB KI SB4 is the basic mounting base Kidde KIR Series detectors GSA LED Remote LED is by this LED resistance wire not exceed Ohms Term Description 1 Not Used 2 DATA IN OUT 3 Not Used 4 DATA IN 4 Remote LED 5 Remote LED 6 Not Used 7 DATA OUT IN IN Signature Controller Previous Device OUT OUT Next Device Detector Base KI IB KI IB4 base includes a built in line fault isolator for use on Class A A detector must be installed for it to operate The isolator does not support the GSA LED Remote LED isolator operates as follows a short on the line causes all iso to open within 23 msec at 10 msec intervals on one side the Class A nearest the loop the isolators to provide the isolator down the with power when the isolator next the short closes it reopens within 10 process repeats beginning on the side of the loop controller Detector Base KI RB KI RB4 base includes a relay Nor Open or Normally Closed is selected during The dry contact is for 1 amp pilot duty Vdc The relay position is to avoid accidentally it out of position The KI RB be operated as a control if programmed to do so at control panel The relay base not support the GSA LED LED Sounder Bases Fire Mode and ABLT sounder bases Setting High for dB cuts SIG OUT DATA DATA CONTACT RATING Amp 30 VDC Duty Term Description 1 Normally Open 2 DATA IN OUT 3 Common 4 DATA IN 5 Not Used 6 Normally Closed 7 DATA OUT Mode Fire jumper for plus CO Setting Temporal jumper for Used 24 Vdc out next base or EOL relay out next KIR Series device Term Description 1 Not Used 2 DATA IN OUT 3 DATA IN 4 Not Used 5 Not Used 6 DATA OUT 7 Not Used Vdc in power supply previous base in KIR Device Control or previous device Cautions detector does not operate without electrical power As frequently cause power interruption discuss further safe with the local fire protection specialist detector does not sense fires in areas where heat cannot the detector Heat from fires in walls roofs or on the side of closed doors may not reach the detector heat detector by itself does not provide life safety protec Use this detector with ionization and or photoelectric detectors detector does not detect oxygen levels smoke toxic or flames Use this device as part of a broad based safety program which includes a variety of information pertaining to heat