Kingfisher 75853 Installation

KFRTI 20 52 A MANUAL Company Foster Avenue Wheeling IL 60090 6574 847 f 847 e mail sales kfco com Internet www kfco com RISK OF ELECTRICAL SHOCK READ THIS INSTALLATION MANUAL COMPLETELY BEFORE OR SERVICING PANELS CHASSIS MUST BE CONNECTED TO EARTH GROUND OBSERVE HOT AND NEUTRAL POLARITY WHEN CONNECTING AC DO NOT APPLY AC OR BATTERY POWER DURING INSTALLATION AVOID INSTALLATION IN DIRECT SUNLIGHT AND IN RAIN RUNOFF DO NOT INSTALL CONDUIT INTO THE TOP SURFACE OF THE SELECTION LOCATE AND INSTALL THE PANEL SO THAT VIBRATION OR WILL NOT CAUSE ACCIDENTAL OPERATION MOUNT PANEL ON A STRUCTURALLY SOUND WALL GENERALLY LOCATION IS A WALL AREA CONVENIENT TO RUN THE FOR ZONE INPUTS ANTENNA AND AC POWER THE PANEL SHOULD BE LOCATED TO PROVIDE A CLEAR VIEW OF AN ARC OF 16 FOR PANEL DOOR CLEARANCE OF SWITCHES AND MAINTENANCE OPERATIONS Company Foster Ave Wheeling IL 60090 6574 847 f 847 e mail service kfco com Internet www kfco com OF ENCLOSURE shall be undertaken only by properly skilled trained and qualified professionals who are in modern industrial installations and all applicable codes and requirements all instructions first not connect batteries or apply power until wiring and installation is complete and checked Co equipment must be installed in accordance with NFPA 72 NFC codes The Electric Code the Local Authority Having Jurisdiction and King Fisher Co manuals and a suitable position and structure for mounting the enclosure REMOVE the subplate s assembly from the enclosure by removing the four 4 nuts and washers 8 nuts washers KFRTI 52 panel REMOVE the mouting hole knockouts located at the rear of the enclosure HOLES HOLES HOLES Company Foster Ave Wheeling IL 60090 6574 847 f 847 e mail service kfco com Internet www kfco com 75853 05 01 1 MOUNT the enclosure on a wall using appropriate hardware shown Use stainless steel hardware for the enclosure in accordance with proper installation requirements MOUNT HARDWARE all conduit necessary to the enclosure must NOT enter through the top of enclosure Knockouts are provided on the and bottom of the cabinet DO NOT knockouts with sub plate s installed conduit to the enclosure using water fittings with star locknuts DO NOT reducing washers S S SCREW S S FLAT WASHER separate conduit runs are required Power Inputs and Audibles Coax Cable Reinstall sub plate s and secure with 4 nuts washers 8 nuts washers in KFRTI 52 panel Remove all PC boards Slide each circuit board out one at a time and lay them down in order on a dry non conductive surface Keep all circuit boards and zone boards in sequence as they are coded for proper transmission MOUNTING SIDE VIEW SIDE VIEW ANCHOR Mtdg Detail WIRING ZONE LUG 2 75853 05 01 Company Foster Ave Wheeling IL 60090 6574 847 f 847 e mail service kfco com Internet www kfco com WIRING wiring must be based on current NFPA National Fire Protection Association and NEC National Code standards Due to varying local and or other building electric and fire codes it is highly that the installer review all applicable codes in addition to NFC National Fire Codes and final acceptance of system installation shall be subject to the authority having jurisdiction drawing 76807 76810 76803 1 and 76806 1 while reading the following instructions Dress field wiring around the bottom and right sides of the enclosure Pull AC wiring into the cabinet The KFRTI 20 52 panel operates on 120 VAC 50 60Hz single phase Connect HOT and NEUTRAL to terminals This panel requires a 15 Amp 120 VAC Circuit or fused circuit to be installed external to the panel Connect Earth ground at the bottom of the to the ground lug s provided Pull Alarm Indicating Wiring into the panel Connect Bell Horns to terminals D1 and D3 and observe polarity If the alarm indicating circuit bells horns sirens etc wiring is longer than 100 feet the panel to EOL device 2 10 11 12 EOL Pull all zone wiring into the enclosure Zone wiring must be connected as per specifications and in with King Fisher instructions and drawings wiring line powered smoke detectors the positive zone terminal 1 4 5 8 must connect to the terminal of each detector A maximum of 2.5 mA can be drawn from each zone supervised wiring is series parallel connected with NO separate runs or taps permitted following diagrams depict Class wiring for use with either the dual zone or the single zone with Class boards when applicable Jumpers W1 W2 and resistor R10 are for programming the Zone Jumpers W3 W4 and resistor R11 are for programming the Right Zone Dual Zone Card Only one side of resistors and jumpers as shown and bend back leaving one leg attached to the board Company Foster Ave Wheeling IL 60090 6574 847 f 847 e mail service kfco com Internet www kfco com 75853 05 01 3 One Side of W1 W2 W3 W4 Activate Class A Zone Wiring PROGRAMMING ZONE CLASS A BOARD One Side of W1 W2 W3 W4 R11 Activate Class A Zone and Release Wiring PROGRAMMING ZONE W RELEASE CLASS A BOARD 2 4 3 K ZONE DEVICES ZONE INITIATING 1 4 ZONE INITIATING ZONE INITIATING following diagrams depict Class wiring for use with either the dual zone or the single zone with Class boards when applicable Jumpers W1 W2 and resistor R10 are for programming the Zone Jumpers W3 W4 and resistor R11 are for programming the Right Zone Dual Zone Card Only one side of resistors and jumpers as shown and bend back leaving one leg attached to the board One Side of R 10 and R 11 Activate Class B Zone Wiring PROGRAMMING ZONE CLASS A BOARD One Side of R10 R11 W3 and W4 Activate Class B Zone and Release Wiring PROGRAMMING ZONE W RELEASE CLASS A BOARD 2 3 4 5 6 7 9 10 11 12 ZONE INITIATING ZONE INITIATING 2 3 4 5 6 7 9 10 11 12 ZONE INITIATING ZONE DEVICES K K K K Install Antenna Reference drawing 76504 or 76506 depending on the type of antenna being installed After connection of field wiring test the panel using the Testing Procedure starting on the following Do not apply power to the panel except as directed in the testing procedure 4 75853 05 01 Company Foster Ave Wheeling IL 60090 6574 847 f 847 e mail service kfco com Internet www kfco com tests should be performed by persons who are familiar with King Fisher radio systems Refer to the Class Operations manual if you are unfamiliar with the product procedure only tests the Panel locally It is highly recommended that all detectors and pull stations be before final approval of the system INSPECT Terminal Connections All wiring should be terminated at a terminal block on one of the Tug on the wires to be sure they are secure and look for exposed metal wires sticking out a terminal which might cause a short or later corrode AC wires should be all the way into the terminal No bare metal exposed Be sure the ribbon cable is properly connected to each mother board and mother board the red stripe is on the left BNC Connection Gently twist conn