Mircom B501-WHITE and B501-IV Installation Manual

File Preview
File Preview
Click below to download for free

File Data

Name mircom-b501-white-and-b501-iv-installation-manual-2857931604.pdf
Type PDF
Size 1.05 MB
Downloads

Text Preview

I Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 10.2 cm 18.8 mm to applicable sensor Operating Temperature Range using the Base Sensor Cross Reference Chart at systemsensor com AND MAINTENANCE INSTRUCTIONS to 32 VDC B501 IV and B501 BL Plug in Detector Bases Diameter Height Temperature Ratings includes base and detector Voltage Current UL268 ULC S529 INSTALLING read the System Smoke Detectors Application Guide which provides information on detector spacing placement zoning wiring and spe applications Copies of this application guide are available from System Observe guidelines for NFPA 72 or CAN ULC S524 depending on This manual should be left with the owner user of this equipment Use only with compatible ULC listed detector heads for proper function The detector used with this base must be tested and main regularly following requirements of NFPA 72 or CAN ULC S536 de on location The detector should be cleaned at least once a year Utiliser uniquement avec des d homologu ULC le bon fonctionnement du syst Le d utilis avec cette base test et entretenu r en conformit avec les exigences de norme CAN ULC S536 Le d doit nettoy au moins une fois an DESCRIPTION B501 WHITE B501 IV and B501 BL are plug in detector bases intended use in an intelligent system with screw terminals provided for power and and remote annunciator connections Communication takes place the power lines and TERMINALS Function 1 TERMINAL LAYOUT Remote Annunciator Annunciator 2 3 PROOF 1 C0131 01 detector base mounts directly to 4 square with plaster ring 31 2 octa 50 mm 60 mm and 70 mm centers AND WIRING GUIDELINES SEE FIGURE 2 wiring must be installed in compliance with all applicable local codes any special requirements of the local authority having jurisdiction Proper gauges should be used The conductors used to connect smoke detectors control panels and accessory devices should be color coded to reduce the of wiring errors Improper connections can prevent a system from properly in the event of a fire signal wiring the wiring between interconnected detectors and modules is recommended that the wiring be no smaller than 18 AWG 0.823 mm sizes up to 12 AWG 3.31 mm may be used with the base system control panels have specifications for allowable loop resistance the control panel specifications for the total loop resistance allowed wiring the detector loops wiring connections by stripping about 3 8 10 mm of insulation from wire end use strip gauge molded in base Then slide the wire under the plate and tighten the clamping plate screw Do not loop the wire the clamping plate See Figure 3 the zone wiring of all bases in the system before installing the detec This includes checking the wiring for continuity correct polarity ground testing and performing a dielectric test base includes an area for recording the zone address and type of detec to be installed at that location This information is useful for setting the head address and for verification of the detector type required for location all detector bases have been wired and mounted and the loop wiring been checked the detector heads may be installed in the bases 2 TYPICAL WIRING DIAGRAM FOR 2 WIRE LOOP A OPTIONAL WIRING Do not loop wire under terminal 1 or 2 Break wire run to supervision of connections EN GARDE Ne pas boucler le fil sous la borne 1 ou 2 le fil pour assurer la supervision des connexions TOWARD CENTER OF BASE SMALL BLADED SCREWDRIVER TO PRESS LEVER IN DIRECTION OF ARROW 4B DETECTOR REMOVAL 3 FEATURE Do not use the tamper resist feature if the removal tool is to be used detector base includes a tamper resist feature that prevents removal of the without using a small screwdriver or similar tool activate this feature use needle nose pliers to break the tab on the detector as shown in Figure 4A Then install the detector remove the detector from the base once the tamper resist feature has been insert a small bladed screwdriver into the small hole on the side the base and push the plastic lever away from the detector head See 4B This allows the detector to be rotated counterclockwise for re tamper resist feature can be defeated by breaking and removing the plas lever from the base However this prevents the feature from being used 4A ACTIVATE TAMPER RESIST FEATURE LEVER TAB AT DOTTED LINE BY TOWARD CENTER OF BASE ANNUNCIATOR RA100Z remote annunciator is connected between terminals 1 and 3 using the lug terminal packed with the remote annunciator The spade lug termi is connected to the base terminal as shown in Figure 5 is not acceptable to have three stripped wires under the same wiring ter unless they are separated by a washer or equivalent means The spade supplied with the model RA100Z is considered an equivalent means See 2 for proper installation 5 CONNECTION TO REMOTE ANNUNCIATOR TERMINAL WIRE WITH SPADE LUG TO PRESS PLASTIC LEVER DIRECTION OF ARROW B501 WHITE B501 IV and B501 BL replace the previous model num B501 and B501A all are functionally the same refer to insert for the Limitations of Fire Alarm Systems LIMITED WARRANTY Sensor warrants its enclosed smoke detector base to be free from defects in ma and workmanship under normal use and service for a period of three years from of manufacture System Sensor makes no other express warranty for this smoke base No agent representative dealer or employee of the Company has the au to increase or alter the obligations or limitations of this Warranty The Company of this Warranty shall be limited to the repair or replacement of any part of smoke detector base which is found to be defective in materials or workmanship normal use and service during the three year period commencing with the date of After phoning System Sensor toll free number 800 SENSOR2 736 7672 a Return Authorization number send defective units postage prepaid to Honeywell Rojas Drive Suite 700 El Paso TX 79936 USA Please include a note describing the and suspected cause of failure The Company shall not be obligated to repair replace units which are found to be defective because of damage unreasonable use or alterations occurring after the date of manufacture In no case shall the be liable for any consequential or incidental damages for breach of this or any Warranty expressed or implied whatsoever even if the loss or damage is caused by Company negligence or fault Some states do not allow the exclusion or limitation of or consequential damages so the above limitation or exclusion may not apply you This Warranty gives you specific legal rights and you may also have other rights vary from state to state Sensor is a registered trademark of Honeywell International Inc System Sensor 03 07 2018

Related Files