Mircom CAT-5131 i3 Series Photoelectric Smoke Detector (Canada) (English)

PHOTOELECTRIC SMOKE DETECTORS SERIES detector line mounting base included wire entry port terminals with SEMS screws to octagonal and single gang 4 square backboxes or direct to ceiling Lock attachment to base cover and chamber for easy cleaning remote maintenance signaling compensation and smoothing algorithms ed sensitivity measurement angle dual color LED indication testing via EZ Walk feature test switch Speci cations smoke detector shall be an i3 Series model listed by Laboratories of Canada ULC The detector be a photoelectric type model C2W BA C4W BA a combination photoelectric thermal model C2WT BA with thermal sensor rated at 135 57.2 detector shall include a mounting base for mounting 3 and 4 inch octagonal single gang and 4 inch back boxes with a plaster ring or direct mount the ceiling using drywall anchors Wiring connections be made by means of SEMS screws The detector allow pre wiring of the base and the head shall be a type The detector shall have a nominal sensitivity 2.5 per foot nominal as measured in the ULC smoke The detector shall be capable of automatically its sensitivity by means of drift compensation smoothing algorithms The detector shall provide color LED indication which blinks to indicate power normal standby out of sensitivity alarm and freeze model C2WT BA C4WT BA conditions When in conjunction with the C2W MOD2A module 2 wire shall include a maintenance signal to indicate the for maintenance at the alarm control panel and shall a loop testing capability to verify the circuit without each detector individually Feature MOUNT OFF TAB TAMPER LOCK TAB i3 series smoke detectors represent a signi cant in conventional detection The i3 family is on three principles Installation Ease Intelligence Instant Inspection Ease i3 line rede nes installation ease with its plug in design allows an installer to pre wire the bases included with heads The large wire entry port and in line terminals ample room for neatly routing the wiring inside base The base accommodates a variety of back box methods as well as direct mounting with drywall To complete the installation i3 heads plug in to base with a simple Stop Drop Lock action detectors offer a number of intelligent features to testing and maintenance Drift compensation smoothing algorithms are standard with the i3 line minimize nuisance alarms When connected to the loop test maintenance module or a panel with the i3 protocol 2 wire i3 detectors are of generating a remote maintenance signal when are in need of cleaning This signal is indicated via LED located at the module and the panel To read the of i3 detectors the CSENS RDRA is a wireless that displays the sensitivity in terms of percent per obscuration Inspection i3 series provides wide angle red and green LED for instant inspection of the detector condition normal standby out of sensitivity alarm or trouble conditions When connected to the C2W loop test maintenance module or a panel with i3 protocol the EZ Walk loop test feature is available 2 wire i3 detectors This feature veri es the initiating wiring by providing LED status indication at each reserves the right to make changes at any time without notice in prices colours materials components equipment speci cations and models and also to discontinue models TO BE USED FOR INSTALLATION PURPOSES NUMBER Diagrams and C2WT AB Wiring Diagram and C4WT BA Wiring Diagram OR OR OR OR OR Speci cations Voltage 12 24 V non polarized 8.5 V 35 V Ripple Voltage of nominal peak to peak Modes Mode up standby of sensitivity trouble Speci cations Temperature Range and C4W BA 0 and C4WT BA 0 Humidity Range to 95 RH non condensing Sensor 57.2 xed Trouble C4WT BA only 41 5 Information Number Current 50 maximum average 50 maximum average Alarm Current 130 mA limited by control panel 20 mA 12V 23mA 24V Standby Current 100 n a Contact Ratings n a 0.5 A 30V AC DC Up Sequence for LED Indication LED status indication seconds LED every 10 secs every 5 secs LED every 10 secs every 5 secs every 10 secs nominal Terminals AWG including base inches 127 mm diameter inches 51 mm height oz 178 grams 3 octagonal back box 4 inch octagonal back box Single gang back box 4 inch square back box with a ring Direct mount to ceiling Current mA max limited by control panel mA max limited by control panel mA 12V 23mA 24V mA 12V 23mA 24V Series 2 wire loop test maintenance module Series Sensitivity Reader Series Retro t Adapter Bracket Removal Replacement Tool TO BE USED FOR INSTALLATION PURPOSES by Interchange Way Ontario L4K 5W3 905 660 4655 905 660 4113 Witmer Industrial Estates Falls NY 14305 Free 888 660 4655 Toll Free 888 660 4113 page http www mircom com Email mail mircom com 5131 3