Mircom CAT-5950 MIX-M500AP (English)

ADVANCED PROTOCOL INTELLIGENT MONITOR MODULES SERIES Designed to meet a wide range of applications SEMS screws for easy wiring Panel controlled status LED except MIX M501MAP Rotary switches for direct dial entry of address Each unit have address set for 01 159 for Advanced Protocol and 01 99 for CLIP mode except MIX M500X standby current Mount in 4 square junction box Zone Interface Module MIX M502MAP Zone Interface Module is a standard module that monitors and supervises compatible two 24 volt smoke detectors on a Style D Class A or Style Class B circuit The module allows Mircom intelligent to interface and monitor two wire conventional smoke All two wire detectors being monitored must be UL ULC compatible with the module The MIX M502MAP is through the communication line of an intelligent system It transmits the status of one zone of two wire to the fire alarm control panel Status conditions are as normal open or alarm The interface module the zone of detectors and the connection of the power supply Isolator Module M500X Isolator Module is a standard sized module enables part of the communications loop to continue when a short circuit occurs on it An LED indicator in the normal condition and turns on during a short condition module will automatically entire loop to the normal condition when the short is removed NUMBER intelligent monitor modules are designed to meet wide range of applications The monitor modules provide interface to contact devices such as manual stations smoke or heat detectors waterflow switches and The monitor modules are addressed with easy to use code switches Advanced Protocol AP devices use a high speed protocol that greatly increases the speed of between the intelligent devices Mircom Protocol uses a superior group polling method as as an interrupt feature that provide for a faster response to alarm condition In addition the Advanced Protocol allows greater system capacity with support for up to 318 devices SLC circuit The AP devices are backwards compatible to in CLIP mode for legacy system applications Monitor Module MIX M500MAP monitor module is a standard sized that supervises either a Style D Class A or Style Class B circuit of dry contact input devices The MIX is intended for use in intelligent two wire systems the individual address of each module is selected the built in rotary decade switches It provides either 2 wire or 4 wire fault tolerant initiating circuit for normally contact fire alarm supervisory or security devices The has a panel controlled LED indicator Mini Monitor Module MIX M501MAP is a miniature monitor module that a Style B Class B circuit of dry contact input The small size of the module allows it to fit devices or junction boxes behind devices The MIX is intended for use in intelligent two wire systems the individual address of each module is selected using decade switches It provides a twowire initiating circuit normally open contact fire alarm and security devices TO BE USED FOR INSTALLATION PURPOSES INFORMATION IS FOR MARKETING PURPOSES ONLY AND INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY Mini Monitor Module Operating Voltage Alarm Current Operating Current Resistance IDC Wiring Resistance IDC Voltage IDC Current Range Isolator Module Operating Voltage Current Current Draw Range VDC uA 1 communication every seconds 47k EOL Ohms Ohms Volts to 120 0 to 49 to 93 Non condensing H 2.75 W 0.65 D 32 VDC not isolating device in isolation to 120 0 to 49 to 93 Non condensing H x 4 W x 1.25 D Monitor Module Operating Voltage Alarm Current LED on 5.0mA LED on to 32 VDC Operating Current Resistance IDC wiring resistance IDC Voltage IDC Current Range 1 communication every 5 47k EOL Ohms Ohms Volts to 120 0 to 49 to 93 Non condensing H x 4 W x 1.25 D Zone Interface Module Operating Voltage Alarm Current Operating Current to 32 VDC LED on 1 communication and 1 flash every 5 seconds 3.9k Ohms Ohms VDC power limited Volts RMS maximum per module to 120 0 to 49 to 93 Non condensing H x 4 W x 1.25 D Resistance IDC wiring resistance Supply Voltage DC Voltage Voltage Range Information suffix A for ULC listed model Module Monitor Module Interface Module Module mount back box white Interchange Way Vaughan ON L4K 5W3 905 660 4655 Fax 905 660 4113 Witmer Industrial Estates Niagara Falls NY 14305 Free 888 660 4655 Fax Toll Free 888 660 4113 INFORMATION IS FOR MARKETING PURPOSES ONLY AND INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY complete and accurate technical information relating to performance installation testing certification refer to technical literature This document contains intellectual property of The information is subject to change by Mircom without notice Mircom does not or warrant correctness or completeness All rights reserved All other trademarks registered trademarks are properties of their respective owners 5950 2