Mircom LT-6917 Wall Installation & Maintenance Manual (English)

AND MAINTENANCE INSTRUCTIONS Series Series Wall Speaker Wall Speaker Strobe Interchange way Vaughan Ontario L4K 5W3 905.660.4655 Fax 905.660.4113 www mircom com ATTENTION NOT PAINT OR ALTER FACTORY APPLIED FINISH IN ANY WAY PAS PEINDRE OU MODIFIER LA FINITION ORIGINALE THIS MANUAL manual is included as a quick reference for For further information on the use of this with a FACP please refer to the panel manual This manual should be left with the owner operator this equipment STROBE DESCRIPTION SPPS 204 speaker strobe is designed to meet S541 requirements for speakers and UL1638 S526 UL 1638A CSA C22.2 No 205 requirements for notification appliances The SPP 204 speaker is to meet UL1480 ULC S541 requirements for 1 MODEL FRONT THE CANDELA SPPS series only candela can be set to 15 30 75 110 185 15 75 for and SPPS 204 70 models 185cd setting is for General Signaling only factory default setting is 15 for SPPS 204 25 70 Pull out the candela selector from the device Re insert the selector tab into the notch that is labeled the desired candela setting when removing or the candela selector ensure to keep it straight Select the candela setting prior to installing the in the mounting plate 2 INSERTING CANDELA SELECTOR THE DIP SWITCHES 3 DIP SWITCH SPPS 204 Series SPP 204 Series 1 SPECIFICATION temperature range flash rate strobe voltage voltage range speaker voltage Size Setting Frequency range wire gauge to 49 to 122 to 93 Hz 1 flash per sec 24VDC VFWR VDC VFWR or 70.7Vrms 1 2 W 4000 Hz AWG For FWR signaling use a Mircom panel Rev 1.1 Jan 22 2021 2 DIP SWTICH 1 FWR Use when flash synchronization is required through a sync module or built in synchronization the control unit when the appliances do not need to be DIP switch 1 default setting is OFF synchronized DIP switch 2 is not used By default it is OFF 4 WIRING TAPS MODELS WITH STROBE FEATURE INPUT POWER NAC SPEAKER POWER WATTS Connect speaker line between C desired wattage This device should be installed as per applicable of the authorities having jurisdiction the information in this document to determine the power or current of the devices The total power or of the devices must not exceed the output rating of panel Refer to the FACP installation guide for the wire required according to the loop length and devices usage For maximum strobe operating current refer to Table 5 When using with Mircom panel or sync module use 3.9K Wiring must be in accordance with CSA C22.1 Electrical Code Part I Safety Standard for Installations section 32 and NFPA 70 ALL TERMINAL TAPS USED FOR SYSTEM SUPERVISION NOT USE LOOPED WIRE UNDER TERMINALS BREAK RUN TO PROVIDE SUPERVISION OF CONNECTIONS PAS UTILISER DE FILS EN BOUCLE SOUS LES BORNES LA LIGNE POUR CONFIRMER LA SUERVISION DES 5 DEVICE CONNECTION recommends spacing speaker strobe appliances in with CAN ULC S524 and NFPA72 Attach the mounting plate to the electrical box with the included mounting screws Insert the device to the mounting plate with 2 screws Attach the top cover with the included securing screw snap the nameplate over the securing screw Select the candela setting prior to installing the in the mounting plate 6 MOUTING DIAGRAM square deep box cover RATINGS 3 SOUND PRESSURE LEVEL OUTPUT SERIES Reverberant Anechoic SERIES Reverberant Anechoic Tap Tap 4 DIRECTIONAL SOUND CHARACTERISTICS of both horizontal and vertical Axis SERIES 75 87 SERIES Interchange way Vaughan Ontario L4K 5W3 905.660.4655 Fax 905.660.4113 www mircom com RATINGS 5 STROBE OPERATING RMS CURRENTS mA Regulated 24VDC Regulated 24VFWR 6 LIGHT DISPERSION of Candela Rating to Floor 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 39 The values in Table 6 are shown as percentages of rated light output at any candela setting Numbers Wall mounted speaker strobe 25V white Wall mounted speaker strobe 70V white Wall mounted speaker strobe 25V red Wall mounted speaker strobe 70V red Wall mounted speaker 25V white Wall mounted speaker 70V white Wall mounted speaker 25V red Wall mounted speaker 70V red End of line resistor 3.9k Ohm