Notifier ACS Series Annunciators ONYX® Series ACM AEM-24AT, ACM AEM-48A

ACS Series Annunciators Series ACM AEM 48A ONYX Series ACS Annunciators provide a modular line products for annunciation and control of the NOTIFIER Series Intelligent Fire Alarm Control Panels Network Annunciators and NOTIFIER legacy addressable The ACS line provides arrays of LEDs to indicate point and in some versions switches to control the state of circuits These ACS units use a serial interface and may located at distances of up to 6,000 feet 1,828.8 meters the panel Speaker control mode for use with XPIQ and the following NFS2 3030 NFS2 640 NFS 320 C and NFS Enables the ACS to control operation of groups of mapped to groups of multi speakers Compatible with existing annunciators Color programmable LEDs On board end of line resistors can be enabled disabled by a switch Alarm Circuit On and Trouble LED per point option or more Alarm only option Touch pad control switch option for remote control of sys relays or silence reset and evacuate LEDs may be programmed to display status of indicating or control relays as well as system status condi System Trouble LED indicator On Line Power LED indicator Alarm and trouble resound with flash of new conditions Local sounder for both alarm and trouble conditions with button program options May be powered by 24 VDC from the panel or by remote supplies Microprocessor controlled electronics fully supervised Slip in custom labels lettered with standard typewriter or program Plug in terminal blocks for ease of installation and service ACS modules are provided in two basic controller mod each with its expander module The ACM 24AT provides annunciation and control points per module each with a green or yellow Alarm Circuit On LED a yellow Trouble and a touch key switch The ACM 48A provides 48 points per module each with a red green or yel Alarm Circuit On LED for annunciating control relays the indicates ON OFF the ACM 24AT each LED point is individually color pro On ACM 48A each column of 24 LED points can color configured using a DIP switch and humidity ranges This system meets requirements for operation at 0 to 49 32 to and at a relative humidity noncondensing of 85 at 86 per NFPA and 93 2 at 32 2 89.6 per ULC However the useful life of the system cid 129 D 95 Control Systems batteries and the electronic components may be affected by extreme temperature ranges and humid Therefore it is recommended that this system and all be installed in an environment with a nominal room of 15 to 27 60 to 80 ACS Series annunciator and control subsystems use hardware assemblies which allow the custom configu of the annunciator panel to fit the individual job require backboxes and mounting hardware schemes includ special remote cabinets allow the annunciators to be con and configured with other system components used with the NFS2 3030 NFS2 640 NFS 320 or leg panels the ACS modules can be used for manual selec of speaker and telephone circuits In this application they typically mounted in the main control near the microphone telephone handset remote annunciation applications the modules are typi mounted in special ABF or ABS boxes Control switch key AKS 1B are available between the ACS Series annunciators and the Fire Alarm Control Panel is made through an EIA 485 costly wiring Four wires are required two for the EIA 485 com twisted pair and two for 24 VDC regulated of ACS Series annunciators into existing systems is accomplished Software may require upgrading and legacy panels may require an interface board field wiring terminations use removable compression type blocks for ease of installation wiring and circuit test eliminating need 2 28 17 Page 1 of 4 ACS Series annunciator and control system provides the system with up to 32 remote serially connected each with a capacity of 96 points for a total of 3072 points subject to the capability of the FACP NFS2 3030 and NCA 2 are capable of using the full 96 or remote power supplies and serial communications the ACS to be located virtually anywhere in the protected NFS 320 NFS2 640 NFS2 3030 NCA 2 and the legacy system alarm and or trouble conditions may be annun on a per point basis or in a grouped or zone configura of system operational controls such as Signal Silence Reset and local annunciation controls such as Local and Lamp Test may be accomplished through module rubber keypad Line Information suffix indicates ULC Listed model see The Annunciator Control Mod contains 24 color programmable red green yellow and 24 yellow Trouble LEDs 24 momentary touch pad a System Trouble LED an On Line Power LED and local piezo sounder with a silence acknowledge switch for indication of alarm and trouble conditions Includes 8.375 21.27 cm high 4.375 11.11 cm wide The Annunciator Expander Module 24AT expands ACM 24AT by 24 system points The AEM 24AT is identi in size and in frontal appearance to the ACM 24AT Up to of these expander modules can be supported by an for a maximum of 96 system points 8.375 21.27 high 4.375 11.11 cm wide NOTE The AEM 24AT can be used to expand the ACM 48A see figure The Annunciator Control Module 48A 48 color programmable red green yellow Active a System Trouble LED an On Line Power LED and a piezo sounder with a Silence Acknowledge switch for indication of alarm and trouble conditions Includes 8.375 21.27 cm high 4.375 11.11 cm wide 2 of 4 DN 6862 D cid 129 2 28 17 The Annunciator Expander Module 48A expands ACM 48A by 48 system points The AEM 48A is identical frontal appearance to the ACM 48A One expander module be supported by an ACM 48A providing a maximum of 96 subject to the capability of the FACP 8.375 21.27 high 4.375 11.11 cm wide NOTE The AEM 48A can be used to expand the ACM 24AT see figure The Annunciator Surface Box 1B provides for the remote mounting of one annunciator in a surface mount enclosure Knockouts are provided use with 1 2 1.27 cm conduit The annunciator mounts to the ABS 1B C without a dress plate 8.5 21.59 high x 4.5 11.43 cm wide x 2 5.08 cm deep NOTE ABS 1B C will not support the installation of the AKS 1B Key Switch The ABS 1TB C is an attractive surface mount for mounting one ACS Series Annunciator Unlike the the ABS 1TB C has an increased depth that mounting of the AKS 1B Annunciator Key Switch 9.938 25.24 cm high x 4.625 11.75 cm wide x 2.5 cm deep NOTE An earlier gray model ABS 1TB will accommodate the ACM AEM 24AT or ACM AEM 48A The deeper ABS 1TB C will accommodate both the ACM or ACM AEM 48A models and the ACM 16AT Series see DN 0524 The Annunciator Surface Box 2B black provides for surface mounting of one ACM 24AT AEM 24AT combina or one ACM 48A AEM 48A combination Knockouts are for use with 1 2 1.27 cm conduit The annunciators directly to the ABS 2B without a dress plate 8.5 21.59 high x 8.92 22.66 cm wide x 2 5.08 cm deep NOTE ABS 2B will not support the installation of the AKS 1B Key Switch see figure The Annunciator Flush Box 1B provides for the remote mounting of a single annuncia module in a flush mount enclosure Knockouts are provided use with 1 2 1.27 cm conduit The ABF 1B includes a black metal trim plate 11 27.94 cm high x 6.25 cm wide mounting hardware and an adhesive annunciator label for the dress plate 9.938 25.24 cm x 4.625 11.75 cm wide x 2.5 6.35 cm deep The