Notifier AMPS-24 & AMPS-24E – Addressable Power Supply – Supplement

Document 51907SUP Rev 51907SUP A 03 552 to the AMPS 24 Manual 51907 Revision A 8 26 2002 Feedback feedback helps us keep our documentation up to date and accurate If you have any comments suggestions about our online Help or printed manuals you can email us include the following information name and version number if applicable manual or online Help Topic Title for online Help Brief description of content you think should be improved or corrected Your suggestion for how to correct improve documentation number for printed manual email messages to note this email address is for documentation feedback only If you have any technical issues contact Technical Services to the AMPS 24 Manual P N 51907SUP A 11 03 2003 Board Layout Figure 1.1 AMPS 24 Board Layout on page 10 Switch Switch Fuse Switch IN OUT IN OUT 4 4 Switch Figure 3.1 and 3.1 Output Figure 2.11 B VOLTAGE cover terminals Output Figure 2.9 A Fault Jumper Cut the jumper JP2 to disable Ground Fault when multiple power supplies are used to other devices that are part of the system such annunciators not disable ground fault detection on the main power supply to the AMPS 24 Manual P N 51907SUP A 11 03 2003 Connecting the Power Cables Figure 2.9 to the Panel Output TB2 on page 18 Red Wire Black Black Red Wire to the AMPS 24 Manual P N 51907SUP A 11 03 2003 Calculation for Main Supply Current Table 4.1 Draw Current Calculations on page 34 Column 1 Non Fire Alarm amps current draw Column 2 Fire Alarm amps current draw Column 3 Non Fire Alarm amps current draw on Terminal Blocks TB2 on on Option refer to Doc 51330 refer to Doc 51330 Loop Backlight ON Backlight OFF NCM F CRM 4RK Auxiliary Relay AA 120 Detector number of LEDs on these during non fire AFM 32A ACM 32A AEM 32A refer to Doc 15712 refer to Doc 15342 refer to Doc 15885 AMG E ATG 2 FFT 7S MMX 2 Refer to Doc 51013 RPT WF RPT F RPT 485WF Communicator optional FC AAM25 Smoke Detectors Supervision Relay Devices not listed Output TB6 Sub totals exceed 1.0 A Output TB2 Sub totals exceed 4.5 A Battery Charger Energy Municipal Box each column for totals 0.120 0.220 0.130 0.100 0.200 0.400 0.200 0.110 0.007 0.001 0.008 0.001 0.007 0.047 0.004 0.025 0.016 0.016 0.002 0.002 0.0054 0.040 0.040 0.002 0.110 0.025 0.100 0.035 0.060 0.060 0.020 0.0094 0.017 0.049 0.040 0.215 0.245 0.020 0.120 0.220 0.130 0.100 0.200 0.400 0.200 0.110 0.072 0.065 0.065 0.080 0.040 0.040 0.047 0.003 0.146 0.087 0.070 0.070 0.056 0.056 0.056 0.056 0.018 0.175 0.065 0.100 0.085 0.060 0.120 0.020 0.090 0.017 0.049 0.100 1.215 2.215 0.020 x 0.120 0.220 0.130 0.100 0.200 0.400 0.200 0.110 0.025 0.0013 0.007 0.001 0.008 0.001 0.007 0.047 0.004 0.045 0.050 0.025 0.016 0.016 0.002 0.002 0.0054 0.040 0.040 0.002 0.110 0.025 0.050 0.035 0.060 0.060 0.020 0.0094 0.017 0.049 0.040 0.215 0.245 0.020 x 0.052 x 0.060 Devices powered by the Panel Output TB2 draw current through the fire panel connection to the power supply Value represents an SLC maximum current draw Refer to device datasheets for individual current draws Total device current cannot exceed 200mA Current consumption of the DPI 232 is dependent upon the baud rate selection via slide switch on the DPI 232 See DPI 232 manual for details Refer to manual and or Device Compatibility Document output 4.2 A when 5V output TB6 is used A when 24V output TB6 is used A when both outputs on TB6 are used to the AMPS 24 Manual P N 51907SUP A 11 03 2003