Notifier APS2-6R 6 0 Amp Auxiliary Power Supply

APS2 6R Amp Auxiliary Power Supply APS2 6R is a state of the art 150 watt switching auxil power supply providing 24 VDC of filtered DC power The provides three 24 VDC output circuits rated for 6.0 in alarm and 4.0 Amps continuous It is used for the of peripheral devices for the Onyx Series control The APS2 6R can also be used with Legacy panels refer to the APS2 6R manual for more information UL 864 Ninth Edition compliant Lightweight compact design 120 or 220 240 VAC 50 60 Hz versions Output circuits with overload protection Built in circuitry Diagnostic trouble LED Plug in connector for in cabinet applications and screw ter for remote device applications Trouble supervision bus Shares battery and charger circuit with control panel Power limited design per UL requirements AC Fail supervision and reporting with field selectable delay Heavy duty clamp type terminals accept up to 12 AWG UL 864 mm wire Battery voltage supervision Low battery disconnect Mounts in a standard CAB 3 CAB 4 Series cabinet and Operation used with the CAB 3 or CAB 4 Series CAB A3 A4 C3 C4 or D3 D4 the APS2 6R mounts to a or CHS 4L mounting chassis If more than one APS2 is necessary to satisfy Audible Visual DC power require connect additional APS2 6R power supplies together described in the Installation Instruction Manual 53232 SPECIFICATIONS primary input power TB1 APS2 6R 120 VAC 50 60 2.9 A APS2 6RE 220 240 VAC 50 60 Hz 1.5 A secondary input power TB3 TB3 1 TB3 2 VDC output power TB2 Total 6.0 A 4.0 A continuous 1 TB2 1 TB2 2 3.0 A 24 VDC power limited Cir 2 TB2 3 TB2 4 3.0 A 24 VDC power limited VDC output power J9 6.0 A 4.0 A continuous Non Limted Contacts TB4 AC Fail supervision over the SLC F2 battery supervision 32 VAC 10.0 A Fast Acting Minifuse supervision bus J3 output Form A contact open J4 input Form A contact open collector E 122 Supplies J3 and J4 can be interchanged of AC indication Immediate indication default 1 2 delay cut JP2 2 3 hour delay cut JP2 and JP3 SPECIFICATIONS APS2 6R measures approximately 8.625 21.91 cm x 16.83 cm x 2.375 6.03 cm and weighs approxi 2 lbs 0.91kg for Mounting Series Use CHS 4 and CHS 4L chassis for NFS2 640 AM2020 AFP1010 NFS 3030 NFS AFP 400 AFP 300 and System 5000 control panels Line Information 24 volt filtered power supply 120 VAC input 24 volt filtered power supply 220 240 VAC input 12 24 VDC end of line relay Four module chassis Four module chassis low profile End of Line Resistor Assembly Standards and Codes power supply complies with the standards set forth by the regulatory agencies Standards NFPA 72 National Fire Alarm Code Laboratories UL 864 Standard for Control Units and Accessories for Fire Systems addition the installer should be familiar with the following NEC Article 300 Wiring Methods Applicable Local and State Building Codes Requirements of the Local Authority Having Jurisdiction 10 22 2009 Page 1 of 2 Listings and Approvals listings and approvals below apply to the basic APS2 6R some cases certain modules may not be listed by certain agencies or listing may be in process Consult fac for latest listing status UL Listed S635 FM approved CSFM 7315 0028 248 FDNY COA 6028 is a registered trademark of Honeywell International Inc by Honeywell International Inc All rights reserved Unauthorized use this document is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice more information contact Notifier Phone 203 484 7161 FAX 203 484 7118 in the U S A 2 of 2 DN 60410 C 10 22 2009