Notifier SpectrAlert® Advance Selectable Output Notification Appliances

SpectrAlert Advance Output Appliances Sensor SpectrAlert Advance selectable output strobes and horn strobes are rich with features guaran to cut installation times and maximize profits The Spec Advance series of notification appliances is designed to your installations with features such as plug in instant feedback messages to ensure correct installa of individual devices and eleven field selectable candela for wall and ceiling strobes and horn strobes specifically when installing Advance products first a universal mounting plate to a four inch square four octagon or double gang junction box The two wire plate attaches to a single gang junction box connect the notification appliance circuit wiring to the terminals on the mounting plate attach the horn strobe or horn strobe to the mounting by inserting the product tabs in the mounting plate The device will rotate into position locking the prod pins into the mounting plate terminals The device will hold in place with a catch until it is secured with a mounting screw Advance products allow you to choose 12 or 24 volts 15 15 75 30 75 95 110 115 135 150 177 or 185 can by way of a rear mounted slide switch and front view window Horn tones and volume by way of a rotary switch The SpectrAlert Advance series includes outdoor notifica appliances Outdoor strobes and horn strobes two and four wire are available for wall or ceiling Outdoor are available for wall only All System Sensor outdoor are rated between and 151 and in wet or dry applications available wall mount horn strobe 2 wire horn strobe 4 wire ceiling mount strobe 2 wire horn strobe 4 wire Outdoor wall mount horn strobe 2 wire horn strobe 4 Outdoor ceiling mount strobe 2 wire horn strobe 4 wire horn strobe Plug in design Same mounting plate for wall and ceiling mount units Shorting spring on mounting plate for continuity check installation Captive mounting screw Tamper resistance capability Field selectable candela settings on wall and ceiling units 15 75 30 75 95 110 115 135 150 177 185 Automatic selection of 12 or 24 volt operation at 15 and 15 candela Outdoor wall and ceiling products Devices Ceiling Ceiling Wall Ceiling Wall Wall Outdoor products rated from and 151 and Outdoor products rainproof per UL50 NEMA 3R and per NEMA 4X IP56 Minimal intrusion into the backbox Horn rated at 88 dbA at 16 volts Rotary switch for tone selection Three horn volume settings Electrically compatible with existing SpectrAlert products Specifications Advance horns strobes and horn strobes shall to a standard 4.0 x 4.0 x 1.5 10.16 x 10.16 x 3.81 backbox 4.0 10.16 cm octagonal backbox or a double backbox Two wire products shall also mount to a single 2.0 x 4.0 x 1.875 5.08 x 10.16 x 4.763 cm backbox A mounting plate shall be used for mounting ceiling wall products The notification appliance circuit wiring terminate at the universal mounting plate Also Spec Advance products when used with the Sync accessory shall be powered from a non coded notifi appliance circuit output and shall operate on a nominal or 24 volts When used with the Sync Module 12 rated notification appliance circuit outputs shall operate 9 and 17.5 volts 24 volt rated notification appliance outputs shall operate between 17 and 33 volts Indoor Advance products shall operate between 32 and 0 and 49 from a regulated DC or full wave recti unfiltered power supply Strobes and horn strobes shall field selectable candela settings including 15 15 75 30 95 110 115 135 150 177 185 11 9 11 Page 1 of 4 strobe shall be a System Sensor SpectrAlert Advance listed to UL 1971 and shall be approved for fire service The strobe shall be wired as a primary sig notification appliance and comply with the Americans Disabilities Act requirements for visible signaling appli flashing at 1 Hz over the strobe entire operating volt range The strobe light shall consist of a xenon flash tube associated lens reflector system COMBINATION horn strobe shall be a System Sensor SpectrAlert Model listed to UL 1971 and UL 464 and be approved for fire protective service The horn strobe be wired as a primary signaling notification appliance comply with the Americans with Disabilities Act require for visible signaling appliances flashing at 1 Hz over the entire operating voltage range The strobe light shall of a xenon flash tube and associated lens reflector sys The horn shall have three audibility options and an option switch between a Temporal 3 pattern and a Non Temporal pattern These options are set by a multiple posi switch On four wire products the strobe shall be powered of the sounder The horn on horn strobe models operate on a coded or non coded power supply PRODUCTS Advance outdoor horns strobes and horn strobes be listed for outdoor use by UL and shall operate and 151 and 66 The products be listed for use with a System Sensor outdoor weather backbox with half inch and three fourths inch conduit MODULE module shall be a System Sensor Sync MDL3R or listed to UL 464 and shall be approved for fire protec service The module shall synchronize SpectrAlert strobes 1 Hz and horns at Temporal 3 Also while operating the the module shall silence the horns on horn strobe over a single pair of wires The module shall mount to 4.688 x 4.688 x 2.125 11.906 x 11.906 x 5.398 cm back The module shall also control two Style Y class B cir or one Style Z Class A circuit The module shall multiple zones Daisy chaining two or more syn modules together will synchronize all the zones control The module shall not operate on a coded power Current Draw Maximum mA RMS 33 V 17.5 V 142 2 of 4 DN 7087 C1 11 9 11 Specifications Standard operating temperature 32 to 120 0 to K Series operating temperature to 151 Humidity range 10 to 93 non condensing indoor 66 Strobe flash rate 1 flash per second Nominal voltage regulated 12 VDC FWR or regulated 24 NOTE Full Wave Rectified FWR voltage is a time varying power source that is used on power supply and panel outputs Operating voltage range 8 V to 17.5 V 12 V nominal or V to 33 V 24 V nominal NOTE P S PC and SC prod will operate at 12 V nominal only for 15 cd and 15 75 terminal wire gauge 12 to 18 AWG 3.31 to 0.821 Ceiling mount dimensions including lens 6.8 diame x 2.5 deep 17.3 cm diameter x 6.4 cm deep Wall mount dimensions including lens 5.6 H x 4.7 W 2.5 D 14.2 cm H x 11.9 cm W x 6.4 cm D Horn dimensions 5.6 H x 4.7 W x 1.3 D 14.2 cm H x cm W x 3.3 cm D Listings and Approvals listings and approvals below apply to SpectrAlert Advance Output