Potter SFH45-75110 SPEAKER SELECT-A-STROBE COMBINATION

A Brand Designed to meet or exceed NFPA ANSI Standards and ADA guidelines Mounts to 4 square back box Field selectable taps from 2 4 and 8 Watts UL Listed for wall or ceiling mount Available in 25V RMS and 70.7V RMS Screw terminals capacity up to AWG12 Two eld selectable settings 75 or 110 cd Tamper proof candela selector switch Polarized strobes with wide operating voltage ranges using ltered un ltered FWR input voltage Synchronization requires the SMD10 3A Sync Module Available in red or white housing low pro le re alarm speakers are designed to generate attention grabbing tones and voice commands for emergency signaling applications SFH45 75110 Series are designed with the exclusive Select A Strobe which features a unique candela intensity eld selector switch for the candela output 75cd to 110cd The strobe housing is clearly labeled with vertical lettering The strobe is polarized for to supervised re alarm circuits It is also designed with a xenon ash tube and provides a candela intensity eld selector switch for performance These highly ef cient low pro le speakers are available with eld selectable taps from 2 8 Watts The speakers are in two input voltage models of 25 and 70.7V RMS SFH45 75110 can be synchronized by using the SMD10 3A Sync Module to comply with NFPA recommendations concerning epilepsy when installing two or more visual appliances within the eld of view The strobe signals are listed for indoor use wall under UL 1971 standard Information Number Voltage Voltage RMS Rate Minute Candela or 110 or 110 or 110 or 110 or 110 or 110 or 110 or 110 White White White White Speci cations speaker and visual alarm indicating appliance shall be Amseco model SFH45 75110 or equivalent device and shall be listed under UL 1480 for audible and voice communications approved for re protective service The re alarm speaker shall be capable of reproducing tones or voice commands on 25V RMS or 70.7V RMS Speakers shall provide incremental tap settings of 2 4 and 8 Watts and have a range of 400 to 4000 Hz They shall produce a UL sound pressure level at 10 feet up to 96dBA The strobe shall be listed under UL standard for signaling devices for the hearing impaired and shall be approved for re protection service The candela ouput shall be eld having a dual setting of 75cd or 110cd intensity output The signaling strobe shall operate on 24V DC from a non coded regulated supply or full wave recti ed un ltered supply The strobe shall be designed to produce one signal ash per second with continuously minimum voltage The speaker is capable of ceiling or wall mounting to a 4 x 4 deep back box When strobe synchronization is the strobe shall be compatible with the Amseco SMD10 3A daisy chain or other source of Amseco sync protocol Audible and devices shall be installed in accordance with current NFPA guidelines Electric Signal Company 2081 Craig Road St Louis MO 63146 4161 Phone 800 325 3936 Canada 888 882 1833 www pottersignal com IN USA MKT 8850033 REV A 1 OF 2 a jewelers screwdriver select the light output 75cd or 110cd Brand inches mm Mount box 184 1 19 32 15 140 Square Deep Extension Ring Diagram Panel S L Next or Module Next or cations Input RMS Power Watts Ohms Pressure dB 10ft Response Hz Frequency Cut off Hz Temperature Range 526 Current mA DC FWR 4W 8W 2W 4W 8W 156 1250 140 10 60 RMS Operating mA DC 190 250 FWR 249 320 voltage may be present inside the light assembly even though is not connected If access to the component board is the capacitor must be discharged by touching a wire to ends of the ashtube DO NOT attempt to touch or remove the until the capacitor has been discharged Indoor use only Required Light Output IN USA 8850033 REV A 2 OF 2