Potter SH-24H Series High Intensity Horn Strobe

SH 24H SERIES INTENSITY UL and cUL listed 24 VDC with 95 110 135 150 177 or 185 cd settings 6 distinct candela settings Candela selection view window 33 sound output settings Horn or chime sound output Pre wire back plate Universal back plate mounting single gang double gang octagon or 4 square Single screw mounting Wall mount Indoor only Low current draw SH 24H Select A Strobe Horn Series provides a wide range of light output options in a single device The candela settings a 24 volt DC operation for the 95 110 135 150 177 or 185 The candela setting is displayed through the front window and selectable using a drum wheel horn settings include Temporal Non Temporal March Time a Chime sound The horn also has Low Mid and High volume for each pattern and tone The tones include 2400 Hz Electro Broadband and Chime voltage input can be either regulated DC or full wave rectified 24 volt operation with an operating range from 16 to 33 VDC strobes can be synchronized using a control panel with the Potter sync protocol or a SMD10 3A sync module SH 24H utilizes a universal mounting plate that will mount on a gang double gang octagon and 4 square electrical boxes The plate allows the installer to mount the plate and connect the wire The strobe attaches in a hinge fashion from the top and is by a single mounting screw The strobe completely covers the back plate therefore it can be mounted before other trades is completed and not affect the final look jumper plug is provided to test for correct in the supervisory mode only Do not alarm current through the jumper Installation must comply in accordance with applicable standards 8910005 1A Information Number Number strobe horn chime strobe horn chime Electric Signal Co LLC St Louis MO Cust Service 866 240 1870 Tech Support 866 956 1211 Canada 888 882 1833 www pottersignal com IN USA MKT 8910005 REV C 1 OF 4 SERIES INTENSITY output in precentage when measured from the following per UL 1971 inches mm 127 voltage may be present inside the light assembly even power is not connected If access to teh coponent board required removal or replacement the capacitor must be by touching a wire to both ends of the flashtube NOT attempt to touch or move the assembly until the has been discharged Current RMS Operating Current RMS 24 VDC 24 FWR To determine total draw add desired setting and horn Refer to the instructions for information 1 2 3 4 5 6 7 8 Dipswitch ON Non temporal OFF Temporal Both 2 OFF and 2 ON March Time and 4 ON 2400Hz ON and 4 OFF Electromechanical and 4 OFF Chime OFF and 4 ON Broadband and 6 ON High ON and 6 OFF Mid and 6 OFF Low and 8 ON Horn strobe on 2 wires and 8 OFF Horn and strobe on 4 wires IN USA MKT 8910005 REV C 2 OF 4 SERIES INTENSITY Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 24 VDC 24 FWR 24 VDC 24 VDC Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 24 VDC 24 FWR 24 VDC 24 VDC Hz Hz Hz Time Horn Current RMS Current RMS Current Reverberant Ratings per dBA 10 ft Anechoic Ratings per S525 dBA 10 ft 24 VDC 24 FWR 24 VDC 24 VDC IN USA MKT 8910005 REV C 3 OF 4 Diagram SERIES INTENSITY 8910004 1 Specifications installer shall provide and install the Potter SH 24H Select A The strobe shall have six 6 candela settings The settings shall be selectable using a drum roller and shall the candela setting on the front of the device The horn shall 33 selectable settings configurable by dip switches The sounder be capable of ANSI Temporal Code 3 March Time and produce chime output The horn shall have three distinct volume levels The shall operate at 24 VDC regulated or full wave rectified strobe horn shall have an operating range between 16 and 33 the strobes an by synchronized using a control panel with the sync protocol or the SMD10 3A sync module The strobe utilize a mounting plate that allows the installer to pre wire the plate The mounting plate shall be universal and mount on a gang double gang octagon or 4 inch square box The mounting shall be completely covered by the strobe and shall be secured a single screw The strobe shall be UL listed to standard 1638 Signaling and standard 1971 Signaling Devices for the Impaired In addition the strobes shall be cUL listed to CAN S526 The horn shall be UL listed to standard 464 Audible Devices IN USA MKT 8910005 REV C 4 OF 4