Cerberus Pyrotronics ILP-2 Intelligent Photoelectric Detector 6172

ILP 2 Photoelectric Detectors for MXL and MXLV Photoelectric Detectors for MXL and MXLV Panels Panels AND ARCHITECT SPECIFICATIONS Most Sophisticated Intelligence Available Today Unsurpassed False Alarm Immunity Easily Programmed to Match Specific Location Hazards by a Pre Defined Smoke Profile from the Control Panel On Board Motorola Microprocessor Based Design Innovative Technology Provides High Speed Fault System Detector Communications EEPROM Supervision Protects Critical Detector Highly Resistant to RFI EMI and Humidity Remote Sensitivity Adjustment and Measurement Field Cleanable Photochamber Alarm Indicator LED Two Wire Operation Compatible with SENSORLINK Model FPI 32 Field Program Verify Detector Perform Diagnostic Testing of Detectors EnviroLINK Software Based Automatic Environmental available only when used with MXL Optional Fully Programmable Relay Base and Audible Listed ULC Listed CSFM and NYMEA Approved Cerberus Pyrotronics ILP 2 Intelligent Photoelectric Detector offers the life safety industry the most method of detection and communication today The ILP 2 utilizes advanced algorithms that the detector to distinguish deceptive phenomena optomizing response to actual hazards fires such that from a cigarette or motor vehicle in a parking from an actual fire hazard In addition the ILP 2 provided an extremely high degree of resistance RFI EMI and humidity No other detection system today offers a higher level of protection or false immunity The ILP Series detector uses a state of Motorola microprocessor with EEPROM error checking and supervision algorithms ILP Series intelligent photoelectric detectors are with Cerberus Pyrotronics SensorLINK FPI 32 programmer tester The FPI 32 is a compact por menu driven accessory which makes programming testing detectors faster easier and more reliable than methods The FPI 32 eliminates the need for cum unreliable mechanical programming methods reduces installation and service costs by electronically addresses and functionally testing the ILP before the detector is installed ILP 2 photoelectric detector is compatible with Pyrotronics MXL and MXLV control panels ILP Series detectors are Underwriters Laboratories NUMBER ILP 2 is a plug in two wire photoelectric detector with Cerberus Pyrotronics MXL or MXLV Each ILP 2 detector consists of a dust resistant cleanable photo chamber microprocessor based circuitry with plastic cover and base Electronic packaging uses surface mount type technol The entire electronic assembly is fully protected from transients by shielding and is coated to resist and corrosion ILP 2 photoelectric detector utilizes a light emitting LED and light sensing photodiode assembled in a array so that under normal conditions light transmit by the LED is directed away from the photodiode and throughout the smoke chamber in a controlled The smoke chamber is designed to manage light and extraneous reflections from dust particles other non smoke airborne contaminants in such a way to maintain stable consistent detector operation Cerberus Pyrotronics ILP 2 detector provides the level of detector intelligence available today with a panel link that allows the user to program the for specific fire hazard profiles through simple selection When installing a new ILP 2 detector user simply selects the application from the following Garage Environment software does the rest no guessing on percent of or selecting outdated alarm configuration figures the control panel programs the detector for optimum fire protection mode without hassle and confirmation delays Once optimized for the fire in the area the ILP 2 provides the best detection can buy Should the operator or installer forget to the detector the detector will revert to a default that allows it to operate as a standard ILP 1 detec ILP 2 detector microprocessor uses an integral to store the detector address and other critical parameters which include an assigned pro value for alarm and trouble thresholds microprocessor software employs sophisticated algorithms to identify and disregard false caused by radio frequency RFI and electromag EMI interference and also validates all trouble before annunciating or reporting to the control Communications within the detector itself and also the ILP 2 detector and the control panel or the programming accessory are supervised and against disruption by reliable microprocessor error checking routines Additionally the micropro supervises all EEPROM memory locations and a high degree of EEPROM failure fault tolerance Manufacturer Room Room Storage Air Duct MXL or MXLV applications an ILP series detector it operating status to be normal in alarm or trouble depending on the difference between the alarm value stored in the detector memory and the latest analog measurement The detector then changes in its status to the MXL or MXLV panel In addition MXL and MXLV panels will sample the value of the detector analog in order to determine if those values indicate dust buildup in the photo chamber if so the will indicate that the particular detector requires an ILP series detector alarm condition is confirmed the control panel the detector LED flashes and flashing until the system is reset at the control Also any user defined system alarm function or by event functions are activated Each ILP series is capable of operating one series remote indicator or one auxiliary relay or one audible base sensitivity calibration and identification are supervised by the control panel Detector can be changed from the control panel SensorLINK FPI 32 Program Test accessory is used to and verify the detector address The technician the accessory program mode to enter the desired The FPI 32 will then automatically set and verify address and test the detector The FPI 32 operates on power or rechargeable batteries providing the flexibility convenience to program and test detectors anywhere in the test mode the FPI 32 will perform a series of tests on the ILP detectors without altering the allowing technicians to determine if the detector operating properly or not ILP series detectors may be installed on the same circuits with ID 60 series detectors MSI series boxes TRI series interfaces ICP output control or the CZM series conventional zone modules ILP series detectors can be cleaned in the field as by simply removing first the detector cover then photo chamber cover and cleaning the interior sur of the photo chamber with a clean soft cloth or ILP series detectors use the Cerberus Pyrotronics low surface mounting detector bases Detector base DB 3S mounts to a 4 inch octagonal square or gang electrical box Relay base model DB X3RS to a 4 inch square deep electrical box Audible model ADBI 60 mounts to a 4 inch square deep box When a 4 inch square or 4 inch square electrical box is used an optional trim ring is avail model RA ADB The DB 3S DB X3RS and ADBI 60 use screw clamp terminals for all electrical connec and self wiping contacts for increased reliability bases contain a provision for an optional concealed mechanism model DB LK to prevent unautho removal of the detector head ILP series photoelectric detectors are approved for within the U L specified temperature range of and 38 Data Data of the ILP series of photoelectric detectors a two wire circuit of 18 AWG thermoplastic fixture enclosed in conduit or 18 AWG limited energy cable without conduit if permitted by local build codes Field wiring should conform to local and Electric Codes and to the control panel wiring is permitted only for Style 4 Class B wiring series photoelectric detectors can be applied within the 30 foot center spacing 900 sq ft areas as in NFPA 72 This applications guideline is on ideal conditions specifically smooth ce