Siemens CAB2-BD CAB2-RD Battery Box, Installation Instructions

Installation Instructions CAB BATT R Box Model CAB BATT R Battery Box from Siemens Industry Inc is used to house 55AH batteries for MXL Systems BTX 2 55AH batteries and BTX 3 100AH for FireFinder XLS Desigo Fire Safety Modular Cerberus PRO Modular and 100AH battery sets for the FS 250 and FS 250C Systems The CAB is black and the CAB BATT R is red The CAB BATT R will be referred to in the of this document as the CAB BATT CAB BATT consists of a door and a backbox as shown in Figure 1 The door is hinged left battery box can be placed on the floor directly underneath the fire panel enclo to which it supplies battery backup or it can be mounted on a flat surface with user supplied bolts that are a maximum of 3 8 inch in diameter When used for applications the battery box must be placed on the floor and mounted to the as described on page 2 FOR WIRING 1 Enclosure battery box is for indoor use only in dry environments to installation consider the following Weight and size of the enclosure codes 315 033917 10 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di the battery box Industry Inc Technologies Division a clean dry shock and vibration free surface in a protected environment the battery box directly beneath the fire panel enclosure to which it be wired Knockouts in the battery box may be needed to line up with knockouts in the fire panel enclosure the battery box so that it is clear of obstructions and the front door freely Mark the locations of the two upper mounting bolts of the battery box on the wall Refer to Figure 2 in in in in INDUSTRY INC INDUSTRY INC PARK NJ 07932 PARK NJ 07932 CAB BATT CAB BATT INSTRUCTIONS INSTRUCTIONS 315 033917 315 033917 in in in HOLES 2 Holes for CAB BATT in Drill the two holes located in the previous step and screw in the top bolts a small gap between the wall and each top bolt the battery box over the two top bolts and allow it to slide down over the bolts Mark drill and install the two bottom bolts in the battery box marked all four bolts securely against the back wall of the battery box the batteries in the bottom of the CAB BATT Select a clean dry shock and vibration free surface in a protected environment the battery box directly beneath the fire panel enclosure to which it be wired Knockouts in the battery box may be needed to line up with knockouts in the fire panel enclosure the battery box so that it is clear of obstructions and the front door freely Mark the locations of the two upper mounting bolts of the battery box on the wall Refer to Figure 2 Drill the two holes located in the previous step and screw in the top bolts a small gap between the wall and each top bolt the battery box over the two top bolts and allow it to slide down over the Mark drill and install the remaining two top bolts marked installations using 55 AH batteries mark drill and install the two bolts in the battery box marked as shown in Figure 2 315 033917 10 Applications Seismic applications the CAB BATT must be placed on the floor and mounted to wall using bolts that are 3 8 inch in diameter installations using 100 AH batteries mark drill and install the bottom in the backbox marked as shown in Figure 2 all bolts securely against the back wall of the battery box Place the batteries in the bottom of the CAB BATT To complete the installation for Seismic applications refer to the CAB 55 and CAB 100 BRKT Installation Instructions P N 315 050547 main AC power line must be turned OFF prior to installation Wiring in accordance with local codes and NEC 760 Connections BTX 1 BTX 2 or BTX 3 batteries are required connect them to the system with Battery Cable Conversion Kit P N 545 634222 following the steps listed below the knockouts in the top of the battery box and bottom of the fire enclosure for entry of battery wiring the Battery Wire Assembly to the batteries in the CAB BATT If a wire is required use a minimum of 12 AWG For FireFinder XLS Desigo Safety Modular Cerberus PRO Modular use P N 465 633943 supplied the PSC 12 Refer to Figure 4 and the PSC 12 Installation Instructions P 315 033060 For FS 250 or FS 250C use the Battery Cable Assembly with the FS 250 FS 250C hardware kit Refer to Figure 5 For MXL P N 555 149033 supplied with the MMB 3 Refer to Figure 6 the 12 in long wire assembly connect the two batteries together as in Figure 3 Secure each end of the assembly to the battery with a x 3 4 screw and lock nut the quick disconnects to the positive and negative battery terminals the 10 32 x 3 4 screws and lock nuts supplied the red battery wire to the quick disconnect on the positive terminal the black battery wire to the quick disconnect on the negative terminal PLACES X 3 4 PLACES NUT PLACES BTX 2 OR BTX 3 IN LONG ASSEMBLY 3 BTX 1 2 3 Batteries using Battery Cable Conversion Kit P N 545 634222 26 1 8 x 8 3 8 x 13 3 25 Industry Inc Technologies Division 315 033917 10 CAB 2 FAIL FAIL NET FAIL FAULT 12 FAIL 4A FAIL O N GND N GND in long wire with Wire 465 633943 DISPLAY WIRE WITH KIT FS 250 FS 250C LONG WIRE WITH KIT 4 Battery Connections from FireFinder XLS Fire Safety Modular Cerberus PRO Modular to 5 Battery Connections from FS 250 FS 250C to MXL Wire 6 Battery Connections from MXL to CAB BATT Industry Inc Technologies Division 315 033917 10 security disclaimer products and solutions provide security functions to ensure the secure operation of building comfort safety security management and physical security systems The security functions on these products and are important components of a comprehensive security concept is however necessary to implement and maintain a comprehensive state of the art security concept that is to individual security needs Such a security concept may result in additional site specific preventive to ensure that the building comfort fire safety security management or physical security system for your are operated in a secure manner These measures may include but are not limited to separating networks protecting system components user awareness programs defense in depth etc additional information on building technology security and our offering