Siemens Desigo Fire Safety Modular - Siemens FireFinder XLS Driver Technical Specification Sheet

Specification Sheet No 127 1682 20 2020 Integration Fire Safety Modular DFSM FireFinder XLS Driver on the PXC Series Platform 1 Typical Siemens FireFinder XLS and APOGEE Automation System Configuration Firmware 2 x on System Architecture Siemens FireFinder XLS Driver with Firmware Revision 2 x Figure 1 supports following Monitoring for a maximum of 64 FireFinder XLS panels PMIs TX I O Modules Maximum of 8,000 APOGEE points per driver A maximum of 64 FireFinder XLS panels FireFinder XLS nodes PMIs per driver Infrastructure FireFinder XLS Driver on the PXC Series Platform 2 Typical Siemens FireFinder XLS and APOGEE Automation System Configuration Firmware 3 x on System Architecture Siemens FireFinder XLS Driver with Firmware Revision 3 x supports the following BACnet IP ALN on Firmware 3 x Do not use an Integration Driver as the router Monitoring for a maximum of 64 FireFinder XLS panels PMIs TX I O Modules Maximum of 8,000 APOGEE points per driver A maximum of 64 FireFinder XLS panels FireFinder XLS nodes PMIs per driver Infrastructure FireFinder XLS Driver on the PXC Series Platform Siemens FireFinder XLS Driver can be loaded PXC Modular or PXC 36 hardware When using a P2 ALN the Siemens FireFinder Driver communicates with Insight software APOGEE field panels and controllers and FireFinder XLS system When using a BACnet ALN the Siemens XLS Driver communicates with Insight software other APOGEE field panels controllers and the FireFinder XLS system Siemens FireFinder XLS Driver performs basic monitoring It maps specific Siemens XLS points into the APOGEE Automation so that they can be accessed by standard such as PPCL Equipment Scheduler and Enhanced Alarming modules are supported for control of fans etc however Floor Level Network FLN are not supported When configured to the Siemens FireFinder XLS Driver Instructions 565 715 the Siemens XLS Driver is UL Listed for smoke control UL 864 category UUKL The Siemens XLS Driver will not affect in any way the sequence or safeties programmed into the XLS fire alarm system to Success that all Siemens equipment to be integrated supported by the Siemens FireFinder XLS Driver integration brings the powerful facility capabilities of the APOGEE Automation together with the FireFinder XLS fire alarm Integrating Siemens FireFinder XLS points both systems to operate as a single system reduced operating maintenance training energy costs increased employee productivity diagnostic capabilities and improved information of fire alarm data at the APOGEE System potentially eliminates the need installation maintenance and training for user interfaces Infrastructure fire alarm activity available at the APOGEE System allows the fire alarm system to automated events such as Fan shutdown Smoke control Emergency lighting activation CCTV activations Card access system door control Supported Siemens FireFinder product line has been to Desigo Fire Safety Modular but still works with the FireFinder XLS The Siemens FireFinder XLS also works with the DFSM equipment driver with Firmware Revision 2.8.5 and 3.5.2 been tested and found to be compatible with PMI revision 3 xx 4 xx and 7 xx RPM revision 4.03.0000 and 4.08.0004 revisions may be compatible with the driver but not been tested addition the Siemens FireFinder XLS Driver with Revision 3.5.2 has been tested and found be compatible with the following MLC line Card with MXL Devices DLC and XDLC line card with Desigo detectors VPM Card with VESDA Interface modules FDCIO422 also can be used with DLC as FDOOT441 FDOT421 FDOOTC441 FDO421 FDT421 XTRI R XTRI D XMS S XTRI S XTRI M PAD 5 FireFinder XLS Driver on the PXC Series Platform Information XLS equipment combinations have not been for compatibility and may be unsupported there are any questions regarding FireFinder XLS alarm system contact your local Siemens Compact Series Compact 36 point Ethernet IP or RS ALN Compact 36 point BACnet IP or ALN Information to enable the Siemens FireFinder Driver on PXC Modular or PXC Interface II 115V Interface II 230V F2L088 06 Cable DB9F to DB25M 6ft to use the Adaptive Control added FW 3.5.2 and later Modular Series Modular Ethernet or RS 485 ALN 96 nodes Modular BACnet IP or MS TP ALN FLN nodes TX I O module support Modular Ethernet or RS 485 ALN 96 nodes TX I O module support Modular BACnet IP or MS TP ALN FLN nodes TX I O module support Module three RS 485 FLN in this document is based on specifications believed correct at the time of publication The right is reserved to make changes as improvements are introduced APOGEE APOGEE GO and Insight are registered trademarks of Siemens Industry Inc Other product company names mentioned herein may be the trademarks of their respective owners 2020 Siemens Industry Inc All presented are subject to a cyber security disclaimer which is available at www siemens com bt cyber security Industry Inc Technologies Division Deerfield Parkway Grove IL 60089 4513 1 847 215 1000 feedback is important to us If you have about this document please send them SBT technical editor us sbt siemens com No 127 1682 in the USA 4 of 4