Siemens FireFinder XLS Operation & Installation Manual

FIREFINDER XLS CONTROL PANEL Operation and Maintenance Manual 315 033744 4 Building Technologies Safety WIRING MUST BE DONE AS DESCRIBED BELOW OBTAIN SAFE AND PROPER SYSTEM OPERATION ground the FireFinder XLS enclosure properly see the latest edition of the Electrical Code or CAN ULC S524 01 Canadian Electrical Code for methods Conduit ground is NOT adequate wire the System in compliance with NEC Article 760 refer to the Power Wiring Instructions for the CAB1 Enclosure P N 315 033007 or the P N 315 033009 as applicable ALL CABLE DRAIN WIRES from any conduit or earth grounded box including those in the FireFinder XLS enclosure Connect shield cable drain wire ONLY inside the FireFinder XLS enclosure No wiring used for any of the following can run outside the building a DLC loop an RS 485 network a NAC circuit used for audibles audio and telephone risers an HZM initiating device zone additional wiring refer to this or call Siemens Technologies Technical Support at OF CONTENTS 1 1 1 1 1 2 System 1 3 Modules 1 7 System Modules 1 10 Analog Devices 1 13 2 1 2 1 Guidelines 2 1 3 1 3 1 Mode 3 2 Mode 3 3 Mode 3 6 SYSTEM 4 1 4 1 4 1 Sations 4 1 Operation 4 2 Priorities 4 3 Procedure 4 4 CONTENTS i INSTALLATION OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTS Operation 4 4 Page 4 4 4 9 4 10 Page 4 10 Music 4 12 Groups 4 13 Silence Unsilence 4 13 Group Non Silence 4 14 4 14 to Local Speaker 4 17 Volume Control 4 18 Station Access 4 20 Test 4 21 Manual 4 21 Telephone System 4 21 Group 4 21 Page 4 22 Page 4 22 Alarm Verification Appendix 1 Application Specific Detection Appendix 3 Intelligent Environmental Compensation Appendix 5 Security Point Installation Appendix 7 Silent Knight Model 5129 Appendix 9 Testing Maintenance Appendix 11 Trouble Messages Appendix 13 Index 1 CONTENTS Siemens Fire Safety FireFinder XLS TM Control System is a powerful intelligent fire control system FireFinder XLS utilizes FirePrint most advanced fire technology in the world is designed to provide the most reliable life safety and property at the lowest system life cycle cost available anywhere FireFinder XLS has architected to be easy to install commission and operate The FireFinder XLS is totally modular to satisfy any size building fire alarm needs basic FireFinder XLS control system consists of the PMI operator interface and processor a PSC 12 power supply and battery charger a PTB power termina board a DLC intelligent device loop controller and ZIC 4A zone indicating card basic two loop system can monitor up to 252 intelligent detectors and devices provides up to 12 Amps of 24VDC power for use in driving the basic 4 notifica appliance circuits These supervised notification appliance circuits can be soft configured for a wide variety of functions such as standard NAC operation horns chimes strobes synchronized or non synchronized coded audibles Code 3 Marchtime Zone Coded etc Municipal Tie Leased Line Extin agent releasing FM 200 or Halon or sprinkler pre action and deluge applica The PMI large easy to read VGA display simplifies system operator control adding intelligent loop controller cards FireFinder XLS can be expanded to support to 2500 intelligent detectors and devices spread across a flexible number of DLC The system can also be expanded by adding additional CC 5 cardcages and supplies to support conventional Form C relay modules network interface for remote enclosure communication conventional detectors and devices and state output modules for use in driving graphic annunciators FireFinder XLS system operator interface is designed to make status informa presentation clear and system control functions simple to operate Through the of soft function buttons on the systems display by lighted physical user can easily events or building