Siemens HMS-SZ HMS-DZ Single Dual Action Manual Pull Station, Installation Instructions

Installation Instructions HMS SZ HMS DZ HMS SE HMS DE Spanish versions HMS SP HMS DP Portuguese versions Action Manual Pull Station Model HMS SZ and HMS DZ Manual Stations and Spanish and Portuguese versions from Siemens Inc are field installed addressable devices advanced control panel communication This technology which provides two communication with the control panel an Intelligent Initiating Device The HMS SZ are single action the HMS DZ DE DP are action to Figure 1 to locate the opening on the MS cover that allows access to the holes which are on the HMS printed circuit board TO 1 Cover connect the HMS to the DPU Programmer Tester the plug from the DPU cable provided with the into the opening on the HMS as in Figure 2 Because HMS devices are polarity the programming plug can be inserted into programming holes in either direction NO NO NOTTTTT prevent potential damage to the DPU DO NO NO an HMS to the DPU until at least one wire is from terminals 1 or 2 of the HMS the instructions in the DPU Manual 315 033260 to program the HMS to the desired Record the device address on the label on the HMS front panel The HMS can now installed and wired to the system FROM TAB 2 the DPU Plug HMS SZ and HMS DZ manual stations as well as their Spanish and Portuguese operate with the FireFinder XLS or FS 250 Control Panels via the DLC or FS Device Loop Card HMS manual station housings have a pull down lever that locks in position after a spring loaded switch See Figure 4 To indicate the manual station is the pull down lever remains down and locked until the station is physically HMS DZ DE DP have an additional lever labeled PUSH IN EMPUJE EMPURRE must be operated first models are reset by opening the hinged housing cover with an Allen key and then and locking the cover Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di 1 2 1 2 STYLE 4 6 TO DLC INSTALLATION P N 315 033090 NEXT ADDRESSABLE DEVICE INITIATING CONTROL PANEL PREVIOUS ADDRESSABLE DEVICE GROUND 3 Information Recommended wire sizes AWG minimum 14 AWG maximum Wire larger than 14 AWG can damage the connector When using shielded cable without metal raceway or with raceway the shields should be terminated at the device terminal If the device box is already grounded by another such as being mounted to a grounded structure the wire should be continuous and must be grounded solely at the point origin for example at the control panel When using shielded cable with metal raceway the wiring shields be continuous and grounded solely at the point of origin The ground terminal shall be connected to the grounded device box When using metal raceway without shielded cable connect the ground terminal to the grounded device box Metal raceway should be thoroughly grounded throughout the system All HMS manual stations are polarity insensitive devices Line 1 and supervisory All HMS manual stations draw 1mA 2 can be either line of the DLC or FS DLC loop the manual station boxes throughout the protected area so that they unobstructed readily accessible and located in the normal exit path Place the station according to the regulations of the authorities having jurisdiction Mounting the backplate to a Model SB 5R Backbox as shown in Figure 4 Mounting the backplate to a user supplied single gang switchbox not overtighten the screws Overtightening may distort the backplate in in in INCH DEEP BOX SUPPLIED HINGED BACKPLATE in in 4 The HMS RATINGS FS DLC Loop Current Industry Inc Technologies Division security disclaimer products and solutions provide security functions to ensure the secure operation of comfort fire safety security management and physical security systems The security on these products and solutions are important components of a comprehensive security is however necessary to implement and maintain a comprehensive state of the art security that is customized to individual security needs Such a security concept may result in site specific preventive action to ensure that the building comfort fire safety security or physical security system for your site are operated in a secure manner These may include but are not limited to separating networks physically protecting system user awareness programs defense in depth etc additional information on building technology security and our offerings contact your Siemens or project department We strongly recommend customers to follow our security advisories provide information on the latest security threats patches and other mitigation measures http www siemens com cert en cert security advisories htm Industry Inc Technologies Division PAGE HAS BEEN LEFT INTENTIONALLY BLANK Industry Inc Technologies Division Park NJ A5Q00072472 ID A6V11208372 enUS a