Siemens PIM-1 Peripheral Interface Module, Installation Instructions

Installation Instructions PIM 1 Interface Module Model PIM 1 module from Siemens Industry is an interface for an MXL MXLV MXL IQ to remote peripheral devices such as VDTs and CRTs It connects an RS device or CRT to an MXL MXLV MXL IQ without the peripheral devices protective causing a ground fault The interface at up to 9600 baud without losing any the PIM 1 in the MME 3 in the upper corner provides an isolated RS 232C for an RS 232C printer when used with an System The PIM 1 bidirectional supports a supervised or nonsupervised a CRT or a VDT Do not use a non printer for an NFPA 72 Proprietary UL 1076 system For NFPA 72 Local any EDP listed equipment may be used PIM 1 has one factory installed jumper See 1 for the location of this jumper Set it to the instructions below before install the PIM 1 on the MME 3 G1 jumper disconnects the output of the remote from PIM 1 supervised printers Leave jumper G1 place non supervised printers Cut G1 to any input to the PIM 1 Industry Inc Technologies Division Park NJ 315 091462 14 TERMINAL 1 to the table on Figure 1 the printer output is not regulated by using a busy signal the PIM 1 may overwrite the buffer If the busy signal is not used the data is transmitted without any delay if the printer cannot keep up with the being sent material may be lost use the busy signal select the appropriate printer busy signal from the terminals in the table in Figure 1 the PIM 1 in the upper right hand of the MME 3 backbox Position the so that TB1 is on the left side of the Mount the PIM 1 module with the hardware Make the necessary cable connections for PIM 1 according to the System described below an MXL System without the Voice option Figure 2 With an MKB 2 Use the cable P N supplied with the PIM 1 to P2 on the PIM 1 to P8 on the Use the cable supplied with the MKB 2 to P1 of the PIM 1 to P1 of the ANN 1 With an MKB 1 Use the cable P N supplied with the PIM 1 to the PIM 1 to the MMB 1 2 on MKB 1 Building Technologies Ltd Safety Security Products Kenview Boulevard Ontario 5E4 Canada jumper G1 in if the System is supervised jumper G1 if the has an printer CONNECTIONS This table refers to whether or not the wiring connections are supervised table does not refer to the type of printer used in the System Terminals TB1 8 and 9 are connected together on the PIM 1 The busy signal from the printer prevents the loss of characters if the printer falls behind Refer to the manual for the proper pin usually 11 TB1 3 or 20 TB1 9 1 PC Board Connections an MXLV System with the Voice option Figure 3 Use the cable P N 555 192242 sup with the PIM to connect P2 on the with P8 on the MMB 1 2 Use the cable supplied with the MKB 2 connect P1 on the PIM 1 to P5 on the P4 on the ACM 1 then con to P1 on the ANN 1 in this con an MXL IQ System See Figure 4 Install the PIM 1 on the back of the panel as shown in Figure 4 the PIM 1 so that TB1 is on the side of the board Mount the PIM 1 module on the raised with the hardware provided Using the cable supplied with the PIM 1 PIM 1 P1 to ANN 1 P1 Using the cable supplied with the MKB 4 PIM 1 P2 to SMB 1 2 P8 RATINGS Ratings for the RS 232C Interface VDC Cable Length 25 feet 2 ohms max circuit to Figure 1 to complete the necessary wiring the PIM 1 in other Enclosures PIM 1 can also be installed in the RCC 1 1F or the MSE 2 enclosure For information on configurations refer to the RCC 1 1F Instructions P N 315 095364 or to MSE 2 Installation Instructions P N 315 as appropriate PARAMETERS the communication parameters for the con devices so that they agree with those by CSG M See the CSG M Manual 315 090381 for information on setting the UL requires that the printer be in same room as the MXL MXLV Control RC119 RC319 Supervised Setup TI82OKSR RC119 RC319 must have the codes selected Baud rate to agree with CSG M P8 on the MMB 1 2 P N 555 192242 with PIM 1 supplied the MKB 2 of MKB 2 2 System Without Voice P8 on the MMB 1 2 P N 555 192242 with PIM 1 supplied the MKB 2 of MKB 2 ACM 1 3 System With Voice Option 4 System 315 091462 14