Siemens PMI-2 Person-Machine Interface, Installation Instructions

Installation Instructions PMI 2 Interface Model PMI 2 from Siemens Industry Inc is the user interface for the FireFinder system From the PMI 2 the operator can acknowledge events control the notification appliance circuits and reset the system Detailed information the nature and location of events can also be displayed PMI 2 is used as the primary user interface in CAB1 CAB2 or CAB3 The PMI 2 can also be used as a primary user interface in a REMBOX2 or REMBOX4 enclosure SUPERVISORY SECURITY TROUBLE PMI 2 contains the site specific program as developed in Zeus All logic and supervision is provided by the controller in the PMI 2 SYSTEM FAIL PMI 2 contains a full VGA LCD Touch Screen and LEDs for display system status An audible sounds when there are unacknowledged on the PMI 2 The display is surrounded by keys that are used to the displayed information and to navigate through these Keys are also provided to obtain help and to enter into the features of the PMI 2 Refer to Figure 1 1 User Interface the back of the PMI 2 there are additional diagnostic displays to aid system troubleshooting This is also where the PMI 2 address is set where the connection is made to Zeus for programming Refer to 2 systems configured to provide Smoke Control UUKL refer to the XLS Control Panel System Manual P N 315 034853 labels are available for applications that require French Canadian Spanish Portuguese Brazilian languages These labels need to be ordered separately to the table below for ordering information apply labels remove the backing from the labels and apply them to the PMI 2 to Figure 3 315 050636 1 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di LVM CC 5 PORT 1 2 A B ID 2 3 4 2 Diagnostics ALTERNATE HERE SUPERVISORY SECURITY TROUBLE ALTERNATE HERE SYSTEM FAIL 3 PMI 2 Labels for Alternate Languages Industry Inc Technologies Division 315 050636 1 the Network Address ELECTRICAL POWER prior to installing the PMI 2 in the enclosure the PMI 2 from its anti static bag Set the two digit address using the 10 rotary switches S2 S3 located on the back of the PMI 2 For a standalone panel set the address of the PMI 2 to 01 Be sure to set leading zeros In the Physical View make sure that the PMI 2 is configured at address 253 the PMI 2 is used for networking with other panels set the two digit network to the XNET node address that has been assigned in Zeus Be sure to set zeros For example Node 2 is set at 02 In the Zeus Physical View the HNET of the PMI is automatically set to 253 when operating in an XNET panel table below details the differences between the network address settings in a and a PMI the PMI 2 PMI 2 mounts to the rear of the inner door in the CAB 1 CAB 2 CAB 3 DOOR or REMBOX4 enclosures Select the location of the It can be mounted either in the center or on the left side the inner door when viewed from the outside of the enclo Place the PMI 2 onto the inner door from the rear over the mounting studs in the desired location Secure the PMI 2 to inner door with the four nuts provided Refer to Figure 4 40 inch long 60 wire cable P N 555 133743 connects the PMI to the CC 5 The CC 5 is located in the back of the enclosure the left hand side Connect one end of the cable to J2 on the J2 is marked with on the PMI 2 printed circuit Connect the other end of the cable to P1 on the CC 5 to Figure 5 the PMI 2 to the RNI in a REMBOX2 4 The RNI is in the back of the enclosure on the top left hand side one end of the cable to J2 on the PMI 2 J2 is marked on the printed circuit board Connect the other end the cable to JP1 on the RNI Refer to Figure 6 4 the PMI 2 to the Rear of the Inner Door Industry Inc Technologies Division 315 050636 1 5 the PMI 2 to the CC 5 6 the PMI 2 to the RNI sure that all cables snap fully into their connectors and close the locking levers the top of each cable connector Secure the cable in the back box using cable and the tie down points in the enclosure The cable must have sufficient slack to the inner door to open fully without putting stress on the cable the normal standby condition the PMI 2 displays the site specific custom message time and date and a synopsis of the system status an event occurs in the system the display enters the Alert mode The event is the local audible sounds and the appropriate LED blinks If the event notification appliances to sound the Audibles On indicator lights At the of the screen an acknowledge button is displayed Pressing this button the event and silences the local audible Once all events are acknowl a reset button becomes available in the lower right side of the display If appliances were active two additional buttons appear at the bottom of screen These allow the operator to silence or unsilence the notification appli When the notification appliances are silenced the Audibles Silenced LED The system can only be reset with the notification appliances silenced more events are present in the system than can be displayed on a single screen a bar appears to the right of the event list Pressing the up and down navigation to the right of the LCD allows the operator to move through the list The event is highlighted in the display Pressing the More Info button will display screen showing details relating to the selected event Other buttons also appear at bottom of this screen There is an expanded text message available and a to show all of the devices associated with the event that are active The can return to the previous screen by pressing the ESC button For more on PMI 2 operation refer to the FireFinder XLS Manual P N 315 033744 Industry Inc Technologies Division 315 050636 1