Siemens RC-30U System 3 Confirmation Module, Data Sheet

s 3TM Module RC 30U AND ENGINEER SPECIFICATIONS Variable interrupt period ranging 1 to 60 seconds Variable confirmation period ranging from second to two minutes Zone or system confirmation Placement supervised UL 864 9th Edition Listed NYC Fire Department and City of Chicago Approved Overview Confirmation Module Model RC 30U from Fire Safety is designed to assure against system Alarm event operation which example might result from the occasional of momentary but harmless products of RC 30U will interrupt the transmission of an signal to the system fire alarm control panel for a factory set period of 20 seconds the time period can be made adjustable from 1 to 60 seconds Immediately the interruption period a confirmation is in effect during which time a subsequent signal if present will be sent to the FACP factory set confirmation period is 1 minute however it is dependent the interrupt setting Should an Alarm be present the system will trigger into an condition during the confirmation period Confirmation Module is placement sensitive Modules connected between the Confirmation Module P2 and FACP are not affected by its operation Modules connected to a subsequent receptacle P1 of the Module may be affected This is by which plug zone or system is used system plug orange wire is for basic where a single Alarm interrupt cycle is sufficient see Typical 1 In the basic application a special harness assembly is used between P4 and P5 and any alarm signal from module connected to receptacle P1 will be for a selected period of time from 1 to seconds 20 seconds is the standard setting this period power to the modules on P1 is removed a yellow light emitting LED is illuminated and a system Trouble signal is initiated Further a signal at 20mA is present on a terminal for use a pre signal or for connection to a recording 3 Confirmation Module 3167 Industry Inc Technologies Division Overview continued following the interruption period the power is restored the yellow LED is and the system Trouble signal is This also starts the confirmation period a period during which time will first be passed uninterrupted to the FACP if any Alarm is present and then having the system go Alarm condition confirmation period is variable to the extent occurrences to the duration of the interruption one minute is standard If no Alarm signal present during the confirmation period Model resets automatically and the system to state zone plug white wire is used for applications various Alarm interruption cycles two or more Model RC 30U will be needed see Typical Connection In this application Alarm signals from only connected to receptacles P1 will not interrupted confirmed The interruption and cycle described above apply in a mode A yellow Trouble LED is provided on RC 30U to annunciate a specific Trouble within Model RC 30U RC 30U which occupies two 2 standard positions is placement supervised a system Trouble signal upon removal the system as well as removal of the system zone plug and or the special plug harness provides a system Trouble signal for precise time control of an alarm interruption shall be provided by a Siemens Fire Safety Confirmation Module Model RC 30U module shall be interconnected to System 3 a 10 wire jumper plug and harness assembly is operable with the system main FACP duration for the interruption period shall be of being set at any precise interval the time frames of 1 60 seconds to modules on the confirmation circuit shall removed a system Trouble event shall occur a signal measured at 20mA shall be present a screw terminal during this period At the end this period power shall be restored to the and the confirmation period shall begin Alarm signal from the modules on the circuit received during this period immediately put the system into Alarm If no Alarm signal is received Model shall reset to state A Trouble indicator shall be for Model RC 30U and Humidity Range RC 30U is UL 864 9th Edition Listed for dry locations within a temperature range of 49 2 to 32 3 0 2 and a humidity of 93 2 at a temperature of 32 2 Ratings State Period Period Event for Ordering Confirmation Module 2 spaces Lbs 0.90 Kg Industry Inc Technologies Division Diagram Typical connections for Single Load Multi Load Confirmations Note specific color of Plug or Plug System Plug orange confirms all zones as function of system Alarm commands Zone Plug white may confirm some zones and not others Refer to plug arrangement and modules controlled in above Receptacle P2 is an incoming bus plug that must be connected to the FACP For Operation Model RC 30U will interrupt the transmission of an Alarm signal to the system FACP for a factory set period of 20 However Model RC 30U is adjustable from 1 to 40 seconds immediately following the interruption period A confirmation is in effect during which time a subsequent Alarm signal if present will be sent immediately to the FACP This confirmation as factory set is approximately 1 minute However the confirmation period is dependent upon the interrupt setting If change setting is required consult your authorized Siemens Fire Safety technician Model RC 30U cannot be used to confirm shorting zones Terminals 1 and 2 are provided should a Trouble output delay be desired Remove jumper Terminals 1 and 2 and connect Terminal 1 RC 30U to Terminals 1 and 2 or Model TL 30U and Terminal 2 Model RC 30U to Terminal 3 Model TL 30U The delay of TL 30U must not exceed 200 seconds Industry Inc Technologies Division This marketing data sheet is not intended to be used for system design or installation purposes the most up to date information refer to each product installation instructions Industry Inc Technologies Division Safety Fernwood Road Park NJ 07932 973 593 2600 908 547 6877 www SBT Siemens com FIS in U S A Safety Kenview Boulevard Ontario 5E4 Canada 905 799 9937 905 799 9858 2012 sheet dated 4 03 1