Siemens REMBOX2 REMBOX4 Remote System Enclosures, Installation, Operation and Maintenance Manual

Installation Instructions REMBOX2 R and REMBOX4 R System Enclosures REMBOX2 R and REMBOX4 R Enclosures are used to house a Remote Person Interface PMI PMI 2 PMI 3 an SSD C REM or CAN modules LVM FCM A Fireman Master Telephone FMT can also be installed in REMBOX4 R The REMBOX2 and REMBOX4 backbox and doors are black the and REMBOX4R backbox and doors are red They are identical in all ways and will be referred to in the remainder of this document as REMBOX2 REMBOX4 The REMBOX consists of an outer door an inner door and a backbox shown in Figure 1 1 Enclosure DOOR DOOR and REMBOX4 Enclosures are for indoor use only in dry environments outer door and inner door are permanently hinged left The REMBOX has a 3 4 flange on all four sides of the enclosure which is used for flush mounting applica backbox is mounted on a flat surface with four user supplied bolts that are a of inch in diameter 315 033772 9 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di to installation consider the following the backbox Mounting height for visual and manual access to the Remote Person Machine PMI PMI 2 PMI 3 displayed in the opening of the outer door Weight and size of the enclosure codes Select a clean dry shock and vibration free surface the backbox clear of obstructions so that the front door opens and the controls and indicators are easily accessible preparing the opening to flush mount the REMBOX make sure it does not exceed dimensions of the enclosure Refer to the SPECIFICATIONS section on page 4 for Mark the locations of the two upper mounting bolts of the backbox on the Refer to Figure 2 Drill the two holes located in the previous step and screw in the top bolts a small gap between the wall and each top bolt the backbox over the two top bolts and allow it to slide down over the Mark drill and install the two bottom bolts in the backbox all four bolts securely against the back wall of the backbox FOR FOR 2 Holes For REMBOX2 And REMBOX4 Industry Inc Technologies Division 315 033772 9 compliance with NEC Article 760 all power limited fire protective signaling must be separated a minimum of inch from all of the following wiring within a control panel light 1 or non power limited fire protective signaling conductors meet these requirements the following guidelines must be observed when modules and wiring to this control panel installing power limited field wiring the installer must comply with NEC article which states fire alarm power limited circuits are installed using Types FPL FPLR FPLP or substitute cable provided these power limited cable conductors extending the jacket are separated by a minimum of 0.25 in 6.35 mm or by a noncon sleeve or nonconductive barrier from all other conductors Entering Enclosure Limited Wiring wiring entering the REMBOX is considered power limited Wiring must be in the route and must not overlap any other wiring Wiring in accordance with local codes and NEC 760 the knockouts in the backbox for the entry of field wiring There two knockouts each in the top and bottom of the REMBOX2 and all field wiring into the backbox Do not dress the wiring until the of all the equipment is known the backbox and wiring are installed complete the installation of the REMBOX installing the RNI the optional tamper switch the PMI PMI 2 PMI 3 or SSD C any optional modules FCM 6 LCM 8 SCM 8 OCM 16 SIM 16 FMT LVM the outer door the RNI on the mounting plate in the backbox Refer to the RNI Instructions P N 315 033420 Refer to Figure 3 on page 4 for the of the RNI mounting plate Install the HTSW 1 Tamper Switch Refer to the HTSW 1 Installa Instructions P N 315 033350 Refer to Figure 3 on page 4 for the of the tamper switch knockout slots the PMI PMI 2 PMI 3 or SSD C REM Refer to the PMI PMI INTL Instructions P N 315 033070 the PMI 2 Installation Instructions P 315 050636 the PMI 3 Installation Instructions Document ID A6V10446194 the SSD C REM Installation Instructions P N 315 034773 as applicable any optional OCM 16 or SIM 16 modules using the REMBOX2 4 MP plate Refer to the REMBOX2 4 MP Installation Instructions 315 034211 any optional modules FCM 6 LCM 8 SCM 8 FMT LVM in the inner of the REMBOX Refer to the FCM 6 LCM 8 SCM 8 Installation P N 315 033040 FMT Installation Instructions P N 315 064100 LVM Installation Instructions P N 315 034090 315 033772 9 Industry Inc Technologies Division MOUNTING PLATE BACKBOX BACKBOX 3 Of Knockouts For Tamper Switch SWITCH KNOCKOUT SLOTS blank plates ID SP as needed in the REMBOX2 or REMBOX4 in spaces on the inner door and secure with 10 32 nuts Refer to Table 1 INNER DOOR PLATES insert the same as the ID MP plate bracket plate bracket FCM 6 LCM 8 and modules on studs in door Secured two 10 32 nuts on studs in door Secured two 10 32 nuts to two ID MPs or ID SPs can be on the inner door of a if no PMI PMI 2 PMI 3 is to four ID MPs or ID SPs can be on the inner door of a if no PMI PMI 2 PMI 3 is If a PMI PMI 2 PMI 3 is up to two ID MPs or ID SPs be installed in a REMBOX4 the inner door The inner door can be secured with a 6 32 x 1 2 screw desired the outer door by placing it on its hinges Close the outer door and with key Industry Inc Technologies Division 315 033772 9 x 3 3 4 x 17 5 16 x 3 3 4 x 17 5 16 dimensions given are for the backbox only and do not include the 3 4 flange on four sides Industry Inc Technologies Division 315 033772 9 security disclaimer products and solutions provide security functions to ensure the secure operation of comfort fire safety security management and physical security systems The security on these products and solutions are important components of a comprehensive security is however necessary to implement and maintain a comprehensive state of the art security that is customized to individual security needs Such a security concept may result in site specific preventive action to ensure that the building comfort fire safety security or physical security system for your site are operated in a secure manner These may include but are not limited to separating networks physically protecting system user awareness programs defense in depth etc additional information on building technology security and our offerings contact your Siemens or project department We strongly recommend customers to follow our security advisories provide information on the latest security threats patches and other mitigation measures http www siemens com cert en cert security advisories htm Industry Inc Technologies Division 315 033772 9 PAGE HAS BEEN LEFT INTENTIONALLY BLANK Industry Inc Technologies Division 315 033772 9 PAGE HAS BEEN LEFT INTENTIONALLY BLANK Industry Inc Technologies Division Park NJ Canada Ltd North Service Road East Ontario 0H6 Canada ID A6V10320981 315 033772 9