Siemens TSP-XB Bracket and Front Plate for TSP-40A Logging Printer, Installation Instructions

Installation Instructions TSP XB and Front Plate for TSP 40A Logging Printer FireFinder XLS Desigo Fire Safety Modular Cerberus PRO Modular Systems Model TSP XB U Shaped Bracket and Front Plate are used to mount the TSP 40A Printer in a CAB2 or CAB3 enclosure The TSP 40A provides a paper record of activity of the system You may install one printer for each PMI PMI 2 PMI 3 FCM2041 U2 Desigo Fire Safety Modular FCM2041 U3 Cerberus PRO interface on your system additional information on the FireFinder XLS Desigo Fire Safety Modular Cerberus Modular System refer to the FireFinder XLS Control Panel Installation Operation Maintenance Manual P N 315 033744 the Desigo Fire Safety Modular Manual ID A6V11231620 or the Cerberus PRO Modular Manual Document ID of the TSP 40A in a FireFinder XLS Desigo Fire Safety Modular Cerberus Modular System System requires the following kits 500 634933 500 849949 500 849950 Printer Module U Shaped Bracket and Front Plate Cable Kit U Shaped Bracket and Front Plate are shipped assembled with seven 10 32 provided Remove the nuts and them to one side for later use the Front Plate and set it to side of for the TSP 40A printer to the U bracket by placing the printer over the four studs on the as shown in Figure 1 Make that the Takeup Reel is close the end of the U shaped bracket Secure the module in with the four nuts provided the printer module 1 the TSP 40 in the U Shaped Bracket TSP 40A mounts on four studs in the inner door of a CAB2 or CAB3 enclosure the first row or on the row directly below the PMI PMI 2 PMI 3 XLS FCM2041 Desigo Fire Safety Modular FCM2041 U3 Cerberus PRO Modular interface install the TSP 40A in a CAB enclosure place the U Shaped Bracket with the printer module installed in it over the four studs in the rear of the inner door in place with the four nuts provided with the TSP 40A printer module P N as shown in Figure 2 a TSP 40A is installed in a CAB enclosure only one CC 5 card cage or CC 2 card cage and a PSC 12 power supply can be mounted in the row the printer module Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di 315 049949 6 XLS DESIGO SAFETY MODULAR CERBERUS MODULAR DOOR JP4 ON BACK OI SILK SCREEN NIM 1M OR ON BACK OF PMI 2 PMI 3 FCM2041 U2 DESIGO SAFETY MODULAR CERBERUS MODULAR SCREEN TSP 40A 2 the U Shaped Bracket to the Inner Door 3 the TSP 40A Installation TSP 40A printer modules comes with two cables P N 600 290607 and P N 600 These cables are used only in MXL MXLV System installations The two used in FireFinder XLS Desigo Fire Safety Modular Cerberus PRO Modular installations two conductor power cable and a data cable contained the TSP XC cable kit P N 500 849950 two conductor power cable has a plug on one end that connects to P1 on the The power cable is provided at a length of 5 feet Cut the wire to the length and strip the insulation from the end of the wire 1 4 3 8 The wired end to the terminals on TB 4 of the PSC 12 or PSX 12 with the red wire going the positive terminal and the black wire going to the negative terminal data ribbon cable connects to P3 on the TSP 40A and to either JP4 on the back the Operator Interface OI note that the silk screen on the OI indicates NIM 1M to J13 on the back of the PMI 2 PMI 3 XLS FCM2041 U2 Desigo Fire Safety FCM2041 U3 Cerberus PRO Modular note that the silk screen on the XLS FCM2041 U2 Desigo Fire Safety Modular FCM2041 U3 PRO Modular indicates TSP 40A Both ends of the data cable have the keyed plug that fits only one way onto the connectors to Figure 3 for the location of the terminals on the TSP 40A the two knobs on the printer guide plate and drop the paper guide exposing the printer mechanism the paper dispensing roller the roller through the paper roll and place the paper in the dispenser the loose end of the paper against the printer to Figure 5 Push the Up Lever to the down position to the tension on the roller Feed the loose end of the paper behind the at the top of the printer mechanism the paper by turning the large gear on the right side of the printer clockwise Advance the paper until one inch extends out from printer mechanism the Paper Roll install the paper roll on the TSP 40A follow the steps listed below See Figures 4 5 6 Industry Inc Technologies Division 315 049949 6 4 the Paper UP LEVER POSITION PAPER ROLLER 5 Mechanism Detail 6 the Takeup Reel Industry Inc Technologies Division 315 049949 6 Figure 4 Figure 6 Hold the paper with both hands and gently pull until 12 inches of paper out from the printer mechanism Return the Up Lever to upright position Note the Up Lever must be in the upright for the printer to print the paper through the slot in the guide plate 7 8 Return the guide plate to its normal position and secure it with the two 9 Remove the take up reel by pulling straight out on both sides of the reel Separate the reel by pulling on both ends revealing the paper retention clip Place the loose end of the paper over the larger part of the reel and slide smaller end of the reel over the paper This locks the paper onto the reel Make sure that the drive gear on the reel is on the left side Then put the reel back into the retaining clips Press down until the reel snaps place Be sure that the drive gear engaged the drive motor gear Take up any slack in the paper by turning the takeup reel until the paper taut TSP 40A Front Plate mounts on the front of the inner door of the CAB1 CAB2 or enclosure over the TSP 40A Printer Module Insert the three studs on the back the Front Plate into the holes provided on the U Shaped Bracket and secure with of the nuts provided Refer to Figure 7 the Front Plate for in Plate places 7 the TSP 40A Front Plate Industry Inc Technologies Division 315 049949 6 the Paper Roll the paper roll following the instructions above when the paper supply is low that you do not lose a printed record of messages sent to a full printer buffer paper roll is Siemens P N 450 934935 or Fujitsu P N FTP 040PU004 CLEAR to resume printing after changing the paper roll or wait about five for the printer to resume printing automatically TSP 40A must be enabled in the Zeus Programming Tool in order to operate in a Fire Safety Modular Cerberus PRO Modular System Industry Inc Technologies Division 315 049949 6 security disclaimer products and solutions provide security functions to ensure the secure operation of comfort fire safety security management and physical security systems The security on these products and solutions are important components of a comprehensive security is however necessary to implement and maintain a comprehensive state of the art security that is customized to individual security needs Such a security concept may result in site specific preventive action to ensure that the building comfort fire safety security or physical security system for your site are operated in a secure manner These may include but are not limited to separating networks physically protecting system user awareness programs defense in depth etc additional information on building technology security and our offerings contact your Siemens or project department We strongly recommend customers to follow our security advisories provide information on the latest security threats patches and other mitigation measures http www siemens com cert en cert security advisories htm Industry Inc Technologies Division 315 049949 6 P