Siemens ZIC-4A Zone Indicating Card, Installation Instructions

Installation Instructions ZIC 4A Indicating Card 315 033050 16 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di 3 3 4 and Indicators 4 5 Zones 6 Switch and Jumper Settings 7 Options 7 8 Multiple Power Supplies 9 10 RATINGS 10 11 Follower 11 Supervised Notification Appliance Wiring 12 Supervised Municipal Tie Wiring 13 Leased Line Wiring 13 Releasing Service Wiring 14 Releasing Service Wiring With PSC 12 Power Supply 15 Bell Follower Circuit Wiring 16 Two Channel Audio Wiring 17 Single Channel Audio Wiring 18 Two Channel Audio and Strobe Wiring 19 Single Channel Audio and Strobe Wiring 20 Fire Safety Modular Cerberus PRO Modular Logic 21 Instructions ZIC 4A Indicating Card FAIL FAIL FAIL FAULT 1 ACTIVE 2 ACTIVE 3 ACTIVE 4 ACTIVE Model ZIC 4A from Siemens Industry Inc is a zone card that provides notification appliance circuits the FireFinder XLS Desigo Fire Safety Modular PRO Modular system It has 4 outputs that can configured for Class A or Class B and control of audible visual notification appliances such as horns speakers strobes etc Its outputs can also be configured as to Municipal Tie Releasing Service per NFPA and 2001 or as a connection to a Leased Line remote circuit zone can be configured independently for different as programmed in the Zeus tool and can be automatically by program logic or manually the PMI PMI 2 PMI 3 XLS FCM2041 U2 Desigo Safety Modular FCM2041 U3 Cerberus PRO During the initial power up condition each on the ZIC 4A is configured as a steady NAC Class configuration with 2A current limit The ZIC 4A then a message to the PMI PMI 2 PMI 3 XLS Desigo Fire Safety Modular FCM2041 U3 PRO Modular indicating that it is ZIC 4A supports synchronized and non synchronized This selection is available in the Zeus tool under detail properties for each ZIC 4A circuit Synchroniza across multiple ZIC 4A cards is automatic as a part of FireFinder XLS Desigo Fire Safety Modular Cerberus Modular operating characteristics Refer to docu P N 315 096363 for a list of strobes that support A Class B circuit configuration can be configured independently have independent input source for each output input voltage supervision output supervision self restoring power limiting signal synchronization capability level Ground Fault detection H Net protocol Uploadable firmware update to pass through up to 3A per circuit features are as follows 1 Zone Indicating Card 315 033050 15 Inc Inc Inc Industry Inc Inc TTTTTececececechnologies Di Di Di Division Di ZIC 4A contains four Class A circuits Each circuit is rated at 3A at 24VDC and an input connected to the power source and an output where the NAC devices Tie Releasing service and Leased Line remote monitoring device are The zone inputs are isolated from one another and are supervised for the of power This allows the use of different power sources with different references The zone output is supervised for open and short circuit condi while the zone is inactive and allows different combinations of output configura Standard NAC Releasing etc per card Each ZIC 4A card occupies any one slot in the CC 5 cardcage The ZIC 4A also has the capability to detect ground on its zone output as indicated by a diagnostic LED and Indicators front panel of the ZIC 4A contains one reset switch thirteen LEDs and three address switches as shown in Figure 1 reset switch is located on the top of the front panel Pushing the reset switch the ZIC 4A operation LEDs follow the reset switch and their functions are defined as follows FAIL FAIL FAIL FAULT 1 ACTIVE 2 ACTIVE ON When illuminated indi that power for the ZIC 4A is to the card OFF When illuminated indi that the card microprocessor has OFF When illuminated indicates the CAN communication with the has terminated and the card goes degrade mode applicable only when resides in a CAN network NOT for FireFinder XLS Desigo Fire Modular Cerberus PRO Modu applications OFF When illuminated indi that the HNET communication with ZIC 4A has terminated and the card into degrade mode applicable only card resides in the HNET network OFF When illuminated indi that the ZIC 4A has detected either negative or positive ground fault on its wiring OFF When illuminated indi that Zone 1 is active OFF When illuminated indi that the ZIC 4A has detected a on Zone 1 open circuit or short OFF When illuminated indi that Zone 2 is active Industry Inc Technologies Division 315 033050 16 rotary dial switches at the bottom of the front panel are used to set the HNET address of the ZIC 4A following components must be set prior to inserting the card to the CC 5 refer Figure 2 3 ACTIVE 4 ACTIVE OFF When illuminated indi that the ZIC 4A has detected a on Zone 2 open circuit or short OFF When illuminated indi that Zone 3 is active OFF When illuminated indi that the ZIC 4A has detected a on Zone 3 open circuit or short OFF When illuminated indi that Zone 4 is active OFF When illuminated indi that the ZIC 4A has detected a on Zone 4 open circuit or short Primary Bell Follower Select Switch switch selects Zone 1 as the Primary Follower Toggle the S1 switch the bottom of the board if Zone is configured as a Primary Bell Follower toggle it to the top of the for normal operation as shown in 2 Leased Line Select Switches These select t