Silent Knight A05-0396 Chimes & Shime Strobes

Selectable Output and Chime Strobes Advance selectable output chimes and are rich with features guaranteed to cut times and maximize pro Advance selectable output chimes and chime are private mode noti appliances used to alert trained to investigate possible emergency situations and to take action Security guard and nurse workstations are ideal for chime products design Advance chimes and chime strobes are rich with guaranteed to cut installation times and maximize pro SpectrAlert Advance Series of noti appliances is designed simplify your installations with features such as plug in designs feedback messages to ensure correct installation of individual and seven candela settings for chime speci when installing SpectrAlert Advance products a universal mounting plate to a four inch square four inch single gang or double gang junction box Then connect noti appliance circuit wiring to the SEMS terminals on the plate attach the chime or chime strobe to the mounting plate by the product tabs in the mounting plate grooves The is rotated into position locking the product pins into the plate terminals The device will temporarily hold in place a catch until it is secured with a captive mounting screw Advance products allow you to choose 12 or 24 volts 24 volts 15 15 75 30 75 95 110 or 115 candela by way of rear slide switch and front view window Select chime tones and volume using a simple rotary switch spring on mounting plate for pre installation continuity mounting screw screw for tamper resistance candela settings 15 15 75 30 75 95 110 115 selection of 12 or 24 volt operation at 15 and 15 75 intrusion into the back box switch for tone selection volume settings compatible with existing SpectrAlert products for ceiling or wall mounting Listings chime strobes chimes Current Draw Data Max Chime Current Draw mA RMS Pattern Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop data represents coding at 3 chimes per second Actual current draw will vary depending upon coding selected Volts Volts Max Chime Strobe Current Draw mA RMS Volts Volts Volts Volts Input Second Chime High Second Chime Low Second Chime High Second Chime Low Chime High Chime Low Second Whoop High Second Whoop Low Time Chime Input Second Chime High Second Chime Low Second Chime High Second Chime Low Chime High Chime Low Second Whoop High Second Whoop Low Time Chime cannot be powered with a coded supply Selection tone selection is accomplished by using the rotary switch on the back of the product The current draw and sound measurements for chime tone settings are listed below Patterns and Chime Strobe Output dBA Pattern Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Test Chime coded High Rate Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Test Chime coded Volts Volts Level Advance Specifications Speci Advance chimes and chime strobes shall mount to a standard 4 4 1 back box 4 inch octagon back box single gang 2 4 17 8 inch box or double gang back box A universal mounting plate shall be used for mounting products The noti appliance circuit wiring shall terminate the universal mounting plate Also SpectrAlert Advance products when used with the Sync Module accessory shall be powered from a non coded appliance circuit output and shall operate on a nominal 12 or 24 volts When used with the Sync Module 12 volt rated appliance outputs shall operate between nine and 17.5 volts 24 volt rated noti appliance circuit outputs shall operate between 17 and 33 volts Indoor Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full wave recti un power supply Chime shall have candela settings of 15 15 75 30 75 95 110 and 115 Combination chime strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1638 and UL 464 The chime strobe shall comply with the with Disabilities Act requirements for visible signaling appliances at 1Hz over the strobe entire operating voltage range The strobe light consist of a xenon tube and associated lens re system The chime shall have two audibility options and an option to switch between a temporal and a non temporal continuous pattern These options are set by a multiple position switch protective service The module shall synchronize Module module shall be a System Sensor Sync listed to UL 464 and shall be approved for strobes at 1Hz and chimes at temporal three Also while operating the strobes the module shall silence the chimes on chime strobe models over single pair of wires The module shall mount to a 411 16 411 16 21 8 inch back box The module shall also control two Style Y class B circuits or one Style Z A circuit The module shall synchronize multiple zones Daisy chaining two or more synchronization modules together will synchronize all the zones they The module shall not operate on a coded power supply Speci Operating Temperature Range Flash Rate Voltage Voltage Range2 terminal wire gauge dimensions including lens dimensions red back box skirt white back box skirt Full Wave Recti FWR voltage is a non time varying power source that is used on some power supply and panel outputs CHS products will operate at 12 V nominal only for 15 and 15 75 cd to 120 0 to 49 to 93 non condensing per second 12DC FWR or regulated 24DC FWR1 to 17.5V 12V nominal or 16 to 33V 24V nominal to 18 AWG in L 4.7 in W 2.5 in D 142 mm L 119 mm W 64 mm D in L 4.7 in W 1.3 in D 142 mm L 119 mm W 33 mm D in L 5.0 in W 2.2 in D 151 mm L 128 mm W 56 mm D in L 5.0 in W 2.2 in D 151 mm L 128 mm W 56 mm D Advance Dimensions