Silent Knight SWIFT Instruction Manual for WSK-MONITOR

I Clintonville Road Northford CT 06472 1610 203 484 7161 Fax 203 484 7118 AND MAINTENANCE INSTRUCTIONS Monitor Module Operating Voltage Current Draw Operating Current Resistance IDC Wiring Resistance IDC Voltage Average IDC Current Transmit RF Power Frequency Range Range Type Life Replacement VDC mA LED on 3.9k EOL Ohms Ohms Volts dBm MHz to 120 0 to 49 to 93 Non condensing Panasonic CR123A or 4 Duracell DL123A year minimum TROUBLE BATTERY LOW display and or during annual maintenance in H x 4 in W x 1 in D Electrical Box preferred mounting option 1 CONTROLS AND INDICATORS INSTALLING information is included as a quick reference installation guide Refer to control panel installation manual and the SWIFT Wireless Manual for de system information If the modules will be installed in an existing op system inform the operator and local authority that the system will temporarily out of service Disconnect power to the control panel before the modules This manual should be left with the owner user of this equipment DESCRIPTION WSK MONITOR Monitor Module is intended for use with a wireless gate or wireless fire alarm control panel FACP to interface with a device contacts used to signal status conditions The input to the monitor is non latching and does not require a reset The device communi through a robust bi directional mesh network to the gateway and or Rotary dial switches are provided for setting the module address The has a panel controlled LED indicator Figure 1 faceplate includes a magnet for activation and tamper resistance Figure The faceplate magnet activates communication to the panel therefore the must be installed for the module to work properly The magnet also a supervisory tamper fault at the panel if the nameplate is removed NOT remove this magnet The faceplate for a wireless module CANNOT be with the faceplate of a standard wired module REPLACEMENT battery levels on the wireless devices are displayed as a trouble in an Therefore when the message BATTERY LOW is dis replace the battery in the device This message is an indication that one week of battery life remains REQUIREMENTS ensure proper operation this module shall be connected to a compatible Knight system control panel list available from Silent Knight replace the batteries in a wireless device use the following steps Have 4 CR123A or DL123A batteries available Remove the faceplate from the module Open the battery compartment refer to Figure 3 Remove the used batteries and replace with new batteries The battery com is designed such that the batteries can only align in the appropri direction Do not force the batteries into the openings Replace the battery compartment cover Replace the faceplace 2 FACEPLATE INTERIOR LOCATION NOT REMOVE 3 BATTERY COMPARTMENT 4 MODULE MOUNTING technologies can exhibit communication disruption if devices are too close together To avoid this form of disruption SWIFT devices not be placed closer than 2 feet 60 cm apart without an intervening WSK MONITOR mounts directly to an SMB500 electrical box see Figure To avoid interference with the wireless network metal electrical boxes are recommended Non metal surface mounted electrical boxes SMB500 available from Silent Knight If not using an SMB500 the minimum opening dimensions for the WSK MONITOR are 4 in X 3 in x in deep Do not attach the module to temporary structures such that the place could be altered All wiring must conform to local codes ordinances regulations This module is in for power limited wiring only must be within 3 of monitored device when using wiring or 20 feet in non metallic Install module wiring in accor with the job drawings appropriate wiring dia Set the address on the module job drawings Secure module electrical supplied by installer as in Figure 4 5 TYPICAL MONITORING CONFIGURATION ONE UL LISTED CONTACT MAY BE USED MODULE EOL LIMITED VDC MAX CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS MUST BE WITHIN 3 FEET OF MONITORED DEVICE WHEN FIELD WIRING OR 20 FEET IN NON METALLIC CONDUIT of these products in combination with non Honeywell products in a wireless mesh or to access monitor or control devices in a wireless mesh nework via the inter or another external wide area network may require a separate license from Sipco LLC more information contact Sipco LLC or Ipco LLC at 8215 Roswell Rd Building 900 950 Atlanta GA 303350 or at www sipocollc com or www intusiq com device complies with part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation Do not make changes to the equipment Changes or modifications not expressly approved by the manufacturer could void the user authority to operate the equipment Knight and Honeywell are registered trademarks of Honeywell International Inc Honeywell 03 02 STATEMENT STATEMENT