Simplex 2098-9576 Installation Manual

File Preview
File Preview
Click below to download for free

File Data

Name simplex-2098-9576-installation-manual-4512897036.pdf
Type PDF
Size 1.18 MB
Downloads

Text Preview

SSimplex 9203 9208 Detectors Photo w Heat Detector 2098 9576 Ionization Detector installing there detectors make a survey of the area to be covered in accordance with information provided NFPA 72 E Sections 4 l through 4 6 an overview of which is provided below For specific applications refer to publication Code Requirements For Fire Alarm Systems Publication No FA2 91 010 For information refer to NFPA 72 E and the NEMA Guide For Proper Use of System Smoke Detectors CONSIDERATIONS there human occupancy Contents to be protected Type of construction and use Burning characteristics of contents Air movement stratification Deflections and obstructions Height of ceilings Surface conditions of ceilings Type of ceiling construction Total area Vent locations velocities dilution detector is capable of providing from 450 to 900 square feet 42 to 84 square meters of coverage depending Requirements of local codes Results of engineering evaluation Physical characteristics of protected area Smooth flat ceiling Detectors may be spaced 30 feet 9 meters apart Ceiling divided by beams of more than 18 in 46 cm depth At least one detector will be required in the space between every two beam Ceiling divided by beams of more than 8 in 20 cm but less than 18 in 46 cm depth Reduce the coverage area for each detector and mount the detector to the bottom of the beams must enter the chamber of the detector Thus air flow air stratification air velocity air stagnation and air will affect detector efficiency Therefore Do not install detectors in areas where temperatures are likely to exceed 100 38 or fall below 32 0 Do not install detectors on a ceiling within 4 inches 10 cm of a wall Do not install detectors where forced air ventilation may dilute the smoke before it reaches the detector Do not install detectors in areas where smoke is normally present kitchens furnace rooms laundry rooms docks rooms with fireplaces rooms with candles soldering rooms etc an 8 digit Product ID number denotes ULC listed product 1993 Simplex Time Recorder Co Gardner MA 01441 0001 U S A 1993 Simplex Equipment Co Ltd Mississauga Ontario L4V 1H3 Canada specifications Manuals Online other were current as of publication are subject change without notice 007 575285 2 93 Do not install detectors in areas where there is likely to be steam in hospital patient rooms with vaporizers near rooms above large sinks etc Do not install detectors above ashtrays in elevator lobbies Wall mounted detectors should be located 4 to 12 inches 1 O 30.5 cm from the ceiling to detector head Protect all detector heads during construction to avoid infiltration of construction debris minimal requirement for detector maintenance should consist of cleaning surface dust by using a vacuum Cleaning programs should comply with NFPA and local environments Cleaning of the internal chamber be done by Simplex technical representative only EQUIPMENT AVAILABLE 553 394 Extendable Smoke Generator 553 533 Sensitivity Tester 553 536 Test and Removal Tool for use with 2098 9201 9202 9203 9576 553 553 Test and Removal Tool Holder for use with 553 536 553574 Test and Removal Tool for use with 2098 9208 testing disconnect city release devices and extinguish systems Notify all appropriate personnel of test The test is with smoke using a 553 394 Extendable Smoke Generator If this method is not acceptable or a functional test can be performed by using a Test and Removal Tool To test the detector place the test around the detector body This will alarm the detector To clear the detector remove the test tool and reset the alarm panel 1 DETECTOR DATA Heat VDC VDC VDC VDC VDC of Detector Voltage Waveform Alarm Current Current Current Element Rating Compatibility Procedure Qty Per Circuit VDC VDC VDC VDC VDC DC DC DC DC DC t Ripple Max 18V Ripple Max 18V Ripple Max 18V Ripple Max 18V Ripple Max mA uA uA or mA uA uA mA uA uA mA uA uA 135 Degrees F 1 mA uA uA or Table 4 Table 4 Table 4 Table 4 Table 4 CAUTION Do not use the 2098 9208 detector with the 2098 9734 power pack The 2098 9208 does not from a full wave rectified unfiltered DC power source using 2098 9536 four wire base full wave rectified DC can be used Compatibility identifier is the PID model number found on the panel or module and detector base Manuals Online BASE MOUNTING l 2 OCTAGONAL 1 4 OCTAGONAL SQUARE 2 10.16 CM Octagonal Box Furnished Simplex per NEC Article 370 4 QTY OF PER CIRCUIT Note5 Aotel Aote 1 Relay operation cannot be guaranteed unless it is the only device on that zone Panel compatibility Detector compatibility For detailed Exceptions data see wiring diagrams the maximum quantity of 30 bases per initiating circuit are as follows marker is the model number of the module or panel marker is the model number found on the detector Document 841 687 Circuit of Bases 3 PANEL NO Manuals Online detector heads MUST only used with red labeled bases Use in any other will result in a non functioning heads LED 2098 9637 2098 9536 the bases in this instruction in accordance with applicable NFPA standards local codes and the having jurisdiction Failure to follow these instructions may result in failure of the detector to initiate alarm condition Simplex is not responsible for detectors that have been improperly installed tested or WIRING TO TERMINALS AS SHOWN DO NOT LOOP WIRE UNDER TERMINALS BREAK WIRE TO PROVIDE SUPERVISION OF CONNECTIONS Manuals Online 2098 9536 2098 9201 2098 9536 2098 9536 2098 9201 VDC Relay Note 3

Related Files