Simplex 2099-9135 Installation Manual

Overview Manual Stations 9761 9795 9796 9797 Instructions instructions describe installing and setting the address for a manual single action double action or local Installing a manual station of the following tasks Setting the Address The address which uniquely identifies the manual on the MAPNET II channel must be set in two places the dip on the rear of the manual station and through the programmer The must match in both places Wiring Addressable manual stations connect to either a 2120 Multiplex Device Transponder CDT 4020 4100 or 4120 system a twisted shielded recommended wire pair MAPNET and receive power and data over this wire pair Manual stations mount to a variety of standard switch and back Maintaining Depending on the model of manual station you may also to replace a small pane of glass or a glass rod following activation 1 summarizes the features of each manual station model this Publication publication discusses the following topics Page the Manual Station Address the Manual Station Glass Pane Glass Rod 2000 Simplex Time Recorder Co Westminster MA 01441 0001 USA specifications and other information shown were current as of publication and are subject to change without notice Manuals Online A the Manual Station Address manual station has a unique address which is set using a series of dip located inside the manual station The manual station address must the address listed in the specification sheets of the 2120 Job Report or the Programmer Report for the 4020 4100 or 4120 Setting for the 2120 System MAPNET Set the manual station address using Table 2 See Figure 1 for the of the switches Use a small screwdriver or pen to set the switches positioning each dip switch note that 0 equals ON and 1 equals OFF Setting for the 4020 or 4120 System Only Set the manual station address using Table 2 See Figure 1 for the of the switches Use a small screwdriver or pen to set the switches positioning each dip switch note that 0 equals ON and 1 equals OFF The address you set must match the address entered in the 2120 Job Report Mark an address label with the appropriate address for the manual station a box for each dip switch in the ON position Leave the OFF blank Apply the label to the manual station near the dip switches Double check the address before wiring the manual station The address you set must match the address entered in the Report for the 4020 4100 or 4120 system Mark an address label with the appropriate address for the manual station a box for each dip switch in the ON position Leave the OFF blank Apply the label to the manual station near the dip switches Double check the address before wiring the manual station 1 Location of Dip Switches on next page Manuals Online the Manual Station Address Continued and Dip Switch Chart Table 2 to convert a decimal address such as address 7 to its binary This binary number can then be set on the manual station as shown the figure at the top of the table 2 Address Settings IS SHOWN SET AT ADDRESS 7 ON OFF FOR USE SWITCHES 5 THRU 8 THRU 4 1000 0100 1100 0010 1010 0110 1110 Manuals Online the manual station to the MAPNET wire pair using Figure 2 as a Refer to the appropriate 2120 CDT 4020 4100 or 4120 panel drawing for MAPNET to panel connections FROM 4100 4120 OR CDT PANEL TO OTHER 2 Wiring Manual Stations Manuals Online the Manual Station Boxes type of box used depends on whether the manual station is to be installed with the wall or surface mounted Surface Installation Mount the station on a Simplex Back Box No no trim required or a receptacle box such as a Wiremold No DEEP or equivalent with surface trim Flush Installation Use two 3 x 2 x2 gangable switch boxes ganged with flush trim the manual station using Figure 3 as a reference 3 Installing a Manual Station Manuals Online the Glass Pane Glass Rod a Glass Pane 2099 9796 uses a glass pane to cover the T handle used to activate an Follow these steps to replace this pane Refer to Figure 4 for an of this procedure Lift the hammer B to an upright position Position the top edge of the glass pane C under the tab on the manual This tab is located at the top of the opening in which the glass pane Callout D in Figure 4 identifies the location of this tab Fit the bottom of the glass pane into the notch located in the glass retainer E in Figure 4 Push the glass retainer A into place The tab at the end of the glass fits into a slot on the back of the manual station to hold the retainer place Gently lower the hammer back into place 4 Replacing the Glass Pane on next page Manuals Online the Glass Pane Glass Rod Continued a Glass Rod this type of station pulling the T handle down breaks the glass rod located below the handle and activates the alarm Replace the glass rod as below Use a key to open the station Carefully clean any pieces of broken glass from the unit Position the rod in the slot located near the bottom of the station See 5 for the location of the slot Close the station and lock 5 Replacing the Glass Rod Manuals Online Text Manuals Online A