Simplex 2190-9038 Remote Printer Installation Instructions

WARNING HAZARD present printer power ON Static electricity not touch contacts printer circuit boards damage components 2190 9038 Remote Printer a hard copy of 2120 Multiplex 4100 Systems BCS status reports Nurse Call and LX 81 0 Building DIP Switches Jumpers COMPLIANCE certified comply with pursuant Subpart limits of equipment Class 6 computing 15 of the FCC rules For Steps 1 through see Figure 1 connected disconnect printer surge suppressed outlet adapter A from AC outlet The printer checks and new DIP switch settings only when the printer is powered up Surge suppressed outlet adapter is an Electricord XP Cat No A 1491 l C AS At the right side of the printer set switches on SW1 and SW2 as follows or 5100 or 5100 Characters Zero Characters Short Tear Off Quality in Page Length Cut Sheet Mode Skip over Perforation Return Only Characters If printer is printing on paper perforation set SW2 3 the ON position To check DIP switch settings at power up hold down the DRAFT LINE FEED button when turning the switch to the ON position then release the DRAFT LINE FEED button Printer responds with g of the current DIPswitch settings connected disconnect RS 232C connector with internal MOV suppression B or the male DB25 connector shown from printer serial connector C 1 2120 BMUX MASTER CARD 1994 Simplex speciticetions Recorder Co other were current aS of publication are subject change without notice Remove the following printer parts if installed front lid D push feed tractor E and its cover F paper guide paper feed knob H and cut sheet feeder not shown See Figure 2 Remove push feed tractor E by pressing in the tabs on both sides using a screwdriver See Figure 3 2 As shown in Figure 4 release the printer upper case J from its bottom case K using a thin flatblade Insert the screwdriver into each of the two holes in the front of the printer one hole at a time inside each hole gently twist and simultaneously push up the screwdriver until the upper case is from the bottom case SEE STEP 6 BEFORE PULLING THE PRINTER UPPER CASE AWAY BOlTOM CASE FROM 4 As shown in Figure 5 slightly raise the upper case J from the front of the printer Be careful not to pull the cable L out from the upper case Disconnect the other end of the flat cable from Connector CN3 Remove the printer upper case J See Figure 5 5 For Steps 8 and 9 see Figure 6 Set SW1 switches on Serial Interface Board 8143 as follows or 5100 oo Baud Rate Data Word Baud Rate Baud Rate Parity Parity Check Baud Rate Interface Valid OFF position Odd Parity ON position Even parity OFF position Parity Check Disabled ON position Parity Check Enabled SW1 1 l 3 1 4 OFF l 7 ON 1200 baud for 2120 or 4100 or 5100 SW1 1 ON l 3 l 4 l 7 OFF baud for 5001 Off position for attachment to 2120 Command Center For the 2120 Multiplex 4100 Fire Alarm 5001 Nurse call or 5100 BCS printer interface ensure that all are disconnected except for the following jumpers which are connected J5 JRS JNOR and JF Re assemble printer in reverse order of disassembly Connections 2120 Multiolex or 4100 Fire Alarm RS 232C connector with internal MOV suppression B to connect printer to 2120 BMUX or 4103 RS 232 See Figure 1 for where connector plugs into printer and Figure 7 for connection to 2120 or 41 WO Nurse Call the male and female DB25 connectors with pigtails provided with the 5001 9958 package aonnect the DB25 connector to the printer and he female DB25 connector to the 5001 9958 serial printer port of the CPU See Figure 8 Buildina Communications Svstem a 5130 9165 Master Clock Card Rev 2.0 or later Using a female DB9 connector not supplied and male 0825 connector supplied connect the DB9 connector to the 5130 9165 and the DB25 connector to printer See Figure 9 For the 5100 BCS only a female DBS male DB25 printer cable not supplied is available under Part No 88 BMUX CONNECTOR RS 232 CARD USEDR 2190 9038 USEDk 2190 9038 Optional port supervised 7 CPU Serial Printer Port BCS Master Clock Card III W SHIELD MAXIMUM DISTANCE PRINTER 5001 CPU 100 FEET 21 go 9038 8 9 For details on mechanical setup control switches and paper loading consult printer manual 8 94