Simplex 4005 Fire Alarm Adapter Kit ™ Installation Instructions

Cautions and Warnings Adapter Kit Fire Alarm Kit Instructions NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS Upon unpacking your Simplex product inspect the contents of the for shipping damage If damage is apparent immediately file a claim the carrier and notify Simplex HAZARD Disconnect electrical power when making any adjustments or repairs Servicing should be performed by qualified Representatives 4005 4002 Fire Alarm Adapter Kit is designed to allow the 4005 electronics be installed into a 2 4 or 6 unit 4002 back box a 2 unit box is used as an throughout this publication Each kit comes with a 4005 4002 adapter a retainer panel and a ship group containing appropriate mounting harness and installation instructions 4005 9150 Part No 636 783 High Current electronics are shipped without box and door assemblies The 4005 9150 comes with a ship group appropriate mounting hardware and installation operating the following steps the supplied engineering documentation and Figures 1 2 to install a 4005 4002 Adapter Kit All mounting hardware is supplied otherwise noted the correct mounting holes in the 4002 back box by placing the plate into the box to line up the corresponding holes see Figure 1 Screw two No 8 x 5 16 inch long mounting screws Part No 426 033 the two top holes in the back box identified in Step 1 while an 1 8 inch gap from the seated position of each screw Carefully place the teardrop holes of the adapter plate onto the two screws in Step 2 see Figure 1 Allow the plate to hang from the screws will tighten them in the next step the two remaining mounting screws through the bottom screw holes of adapter plate into the back box and tighten all screws Screw four No 8 x 5 16 inch long mounting screws Part No 426 033 into four holes of the adapter plate while leaving an 1 8 inch gap from the position of each screw see Figure 1 for the position of each screw Mount the 4005 electronics assembly to the four screws installed in Step 5 then tighten all screws see Figure 2 Using the 841 986 interconnection diagram check all internal connections necessary remove the existing 4005 battery harness 733 807 and it with the battery harness 733 898 supplied in the adapter kit ship DO NOT connect the harness to the batteries at this time on next page 1996 Simplex Time Recorder Co specifications and information shown were current as of publication and are subject to change without notice B Adapter Kit Continued Using the 841 990 field wiring diagrams connect all field wiring to the Pay careful attention to the routing of Power Limited and Non Power wiring as defined on the Module and Wiring Identification Label No 526 201 located on the back of the retainer panel Maintain a separation of Power Limited and Non Power Limited wiring Module wire point identifications can be written on this label in the spaces to their locations Carefully mount the optional dress panel if present Using the retainer clips mounting screws supplied mount the retainer panel see 2 You must mount both the dress and retainer panels so that the display is visible through the opening in the retainer panel Back Box Plate Electronics Dress Clips 1 Adapter Plate Panel 2 4005 Electronics Assembly High Current Installation four appropriate holes in the back box while leaving an 1 8 inch gap the seated position of each screw the back box Refer to the 4005 Fire Alarm Installation Operating Part No 574 068 for more information the following steps the supplied engineering documentation and Figure 3 to the 4005 9150 High Current electronics assembly into a 4005 back box mounting hardware is supplied unless otherwise noted Mount the 4005 back box according to the instructions found on the label Screw four No 8 x 5 16 inch long mounting screws Part No 426 033 into Mount the 4005 High Current electronics assembly to the four screws Using the 841 986 interconnection diagram check all internal connections Using the 841 990 field wiring diagrams connect all field wiring to the Carefully position the door hinges in line with the back box hinges and including the grounding strap Pay careful attention to the routing of and Non Power Limited wiring as defined on the Module Wiring Identification Label Part No 526 201 located on the inside of door Maintain a 1 4 separation between Power Limited and Non Limited wiring Module and wire point identifications can be on this label in the spaces corresponding to their locations in Step 2 and then tighten all screws see Figure 3 home two hinge pins supplied Strap Back Box Pins Door 3 4005 High Current Electronics Installation High Current Assembly B