Simplex 4010 Series, 4090-9005, 4090-9006, 2975-9277, 4090-9812, 2080-9046 4010ES Automatic Extinguishing, Deluge and Preaction Sprinkler System Releasing Control

ULC Listed FM Approved Control Panels Automatic Extinguishing Deluge and Preaction System Releasing Control control using the Simplex 4010ES Alarm Control Panel to provide Coverage for multiple areas of Automatic Extinguishing and or Deluge and Preaction Sprinkler System including audible escalation of events Control of compatible Listed Approved 24 VDC automatic actuators one per circuit or two 12 VDC actuators in per circuit Releasing appliance circuits RACs by connecting appliance circuits NACs to Suppression Peripherals for actuator supervision and control Four 3 Amp Notification Appliance Circuits NACs in the for use with Suppression Release Peripherals SRP required notification appliances Additional actuator circuit control and additional NACs are using 4009 IDNet Addressable NAC Extenders Suppression Release Peripherals Escalation of Events Temporal or 20 bpm March Time pattern for first alarm 120 bpm March Time pattern indicates releasing timer active On steady indicates releasing timer expired and actuator is NOTE Requires NACs dedicated to conventional horn not SmartSync operation with strobes controlled separate NACs IDNet NAC Extenders provide Up to eight NACs for notification requirements and for input to Suppression Release Peripherals Control is via IDNet addressable communications Suppression Release Peripheral with Dual Command Control Dual command control requires that both IDNet commands and an activated NAC are to initiate the desired release NAC provides wiring supervision to the actuator including of coil continuity and short circuit supervision the coil supervision module Release Peripheral control features An on board DC DC regulator compensates for voltage to the peripheral and ensures proper control circuit over a wide operating range Provides a single RAC for control of actuators for up to 2 using a 3 A NAC input 1 A using a 2 A NAC input system components 4010ES Series control panel with Releasing Appliqu Dedicated NAC output from 4010ES or compatible NAC Coil supervision module one per RAC Maintenance Switch one per RAC Abort Switch connected via an addressable interface listed to Standard 864 supervisory SUPER VISI ON MODUL E 2 AMP 2081 9046 NAC NAC BLK DATE COD E 519 958 YEL ON INSTRUCTION S 574 437 REV AIN 1 4 SEPARATION WEEN POW ER LIMITED S K AND NON PO WER YEL BLK WIRING TIME RECORD ER CO G ARDNER MA USA circuit Switch with indicator lamp 1 DISABLE SUPPRESSION DISABLE Peripheral addressable devices SU PPR ESSION ABORT AND HOLD IDNET IN IDNET IN RELEA SE for lamp if required circuit Control Panel Release Control Simplified Block Diagram combined with Suppression Release Peripherals the series fire alarm control panel provides actuator and control for use in automatic extinguishing deluge or preaction releasing systems Hazard area and notification devices are controlled using either or addressable circuits per standard 4010ES The necessary releasing system logic is within the 4010ES control panel as required for local application Additional listings may be applicable contact your local Simplex product supplier for the status Listings and approvals under Simplex Time Recorder Co are the property of LP Westminster Extinguishing Release Systems System Requirements Continued systems automatically activate electrically actuators for the release of a fire extinguishing such as dry chemical water spray foam CO2 or agent in response to fire detection device inputs as by programming of the host fire alarm control Extinguishing Release System Panels required to have a minimum of 24 hours of standby Initiating devices must be Listed Approved for the and may be wired either Class A or B actuators must be electrically compatible with the panel circuits and power supplies and are wired B to provide coil supervision or Preaction Sprinkler Systems systems automatically activate water control in response to fire detection device inputs Sprinkler Systems employ open sprinkler and provide water flow when the fire detection activates a common automatic water control They are used to deliver water simultaneously all of the system sprinkler heads This type of is applicable where the immediate application of quantities of water over large areas is the proper fire Sprinkler Systems are similar to deluge except that normally closed sprinkler heads are and supervisory air pressure is maintained in the Operation requires both an activated sprinkler head an activated fire alarm initiating device with specific determined at the host fire alarm control System Requirements Releasing actuators are controlled from a Release Peripheral 4090 9005 or Connections are 2 wire Class B releasing with only one 24 VDC actuator per circuit applicable two 12 VDC actuators in series or 12 VDC actuator with manufacturer supplied may be used Coil Supervision Module 2081 9046 must be wired before the actuator and located in the wiring junction box Refer to diagram on 5 The connected RAC provides continuity of the actuator coil and wiring and short circuit supervision to the coil module Cross zoning or other alarm initiation logic per requirements is to be implemented by at the fire alarm control panel UL Listed Automatic Extinguishing Releasing requires that battery standby must be a of 24 hours with 5 minutes of alarm and that actuators are used refer to list on page 6 FM Approved Automatic Extinguishing Release secondary standby to be a minimum of hours with 5 minutes of alarm Actuators must be compatible FM Approved Deluge and Preaction Sprinkler requires that initiating device circuits be A and wired to Listed Approved devices power capacity must be a minimum of 90 with 10 minutes of alarm and that compatible Water Control Valves must be used Refer actuator list on page 7 Maintenance Switches one per RAC are required NFPA 72 the National Fire Alarm Code 2002 Chapter 6 to allow the system to be tested or without actuating the fire suppression Their use may not be allowed in some always confirm local requirements used Simplex Maintenance Switches are to ensure that operation initiates a condition Abort Switches are available when abort operation is When used connect to an addressable IAM model 4090 9001 or similar adapter module The Simplex abort switch the IAM mount in a single gang box 2 1 2 depth Addressable Manual Releasing Stations are used to activation of the releasing actuators with the time delay implemented by the fire alarm panel Notification Requirements Each hazard area requires general audible and visible fire notification and additional dedicated NACs for releasing status notification Suppression is compatible with conventional panel NAC modules as well as for use with the IDNet NAC Extender Additional Suppression Release Peripheral Refer to Installation Instructions 579 385 Releasing Systems Reference additional information refer to Factory Mutual Corporation FMRC Approval Guide Approval standard Systems and Preaction note that proper operation of releasing control requires that the system design installation and be performed correctly and in accordance all applicable local and national codes and manufacturer instructions No liability for system operation is assumed or implied Product Selection