Simplex 4020 Fire Alarm, Jumper and Switch Settings

Bimplex Fire Alarm Placements Switch Settings 1994 Simplex Time Recorder Co specifications other were current as of publication are subject change without notice 574 065 OF CONTENTS Controller Assemblies Master Controller Assy Controller Assy 1 2 Supply Assemblies Supply Supply Slave Board Assemblies Assy 3 Assy 3 Slave Board Assy Slave Board Assy MAPNET Transceiver Assy Optional Board Assy 8 Assy 9 4020 4002 4120 Network Modular Assy 10 to Adjust the NiCad Battery Charger 12 Configuration Jumper Kits are available Fitchburg under Part No 740 769 kit contains No port for Monitor Zone features red wires port for Signal Zone features blue wires port for Security Zone features white wires power supply voltages CONTROLLER ASSEMBLIES MASTER CONTROLLER ASSY Figure 1 JVi U17 1 Package P4 City Connection Configuration Jumpers configure system for city connection jumpers on jumper package P4 where indicated by Xs Table 1 system operation pins 2 and 3 to enable system operation Package P5 Write Enable Jumpers for CFIG EPROM U8 1 1 and 2 to enable CFIG programming CFIG programming JWl and JW2 Factory Installed JW2 out when System Executive EPROM U18 2 Meg in JWl out when System Executive EPROM U18 4 Meg N O Software Reset Switch system microprocessor when pressed causes warm start MASTER CONTROLLER ASSY Figure 2 P5 P7 JWl SW1 2 Package P4 City Connection Configuration Jumpers Table 1 page 1 Package P5 Write Enable Jumper for CFIG EPROM U8 1 and 2 to enable CFIG programming pins 2 and 3 to enable system operation CFIG programming Package P6 Enable Jumper for CFIG File Download 1 and 2 to enable CFIG file to be downloaded pins 2 and 3 to enable CFIG file to be downloaded via Package P7 Enable Jumper for RAM Battery Backup 1 and 2 to enable RAM battery backup at panel startup pins 2 and 3 to disable RAM battery backup at panel JWl and JW2 Factory Installed JW2 out when System Executive EPROM U9 2 Meg in JWl out when System Executive EPROM U9 4 Meg Software Version 7.1 systems require a 4 Meg Executive EPROM N O Software Reset Switch system microprocessor when pressed causes warm start SUPPLY ASSEMBLIES POWER SUPPLY INTERFACE ASSY Figure 3 Compatible with 565 222 Standard Slave Board Assembly 4 Supply Enable Jumpers P3 P4 and P6 Part No 166 250 1 All three jumpers are required system operation 3 2 The are shipped 4020 panel and must be by a Simplex Enables 5V to system and 24V for board use Enables 28.5V power from tap power to 36V converter and system 24V Enables 28.5V power from tap POWER SUPPLY INTERFACE ASSY Figure 4 Compatible with 565 368 Standard Slave Board Assembly 6 BLK TB3 P13 TB4 YEL 1 4 Plug P5 Battery Disconnect pins 1 and 2 System configured pins 2 and 3 System NOTconfigured battery backup battery backup causes trouble indication upon battery disconnection Never jumper pins 2 and 3 to prevent a trouble when batteries are disconnected Plugs P6 and P13 pins 1 and 2 for normal operation across pins 2 and 3 when adjusting NiCad battery charger See page 10 for NiCad battery charger adjustments Supply Enable Jumpers PlO Pll P12 and P14 Part No 166 250 1 These jumpers are all required system operation 2 The shipped 4020 panel and must be by a Simplex 5V power to system and 24V uninterruptable power for board use Plug PlO 28.5V power from tap to TB3 Plug Pll Plug P12 Plug P14 28.5V power from tap to TB2 28.5V power from tap to TB4 when AC power is present at P9 otherwise off An illuminated LED1 indicates that AC power is being applied to the power supply It DOES NOTindicate that power supply present y provides system operating power SLAVE BOARD ASSEMBLIES STANDARD SLAVE BOARD ASSY Figure 7 Switch SW1 Address and Baud Rate Select must be set as shown in Figure 5 Switch SW2 Power Supply Select switches accordance with Table 2 next page 5 Figure 6 depicts SW2 as set during manufacture configuring power supply for sealed lead acid batteries 2 6 565 222 Standard Slave Boards cannot charge NiCad batteries Jw2 JWl and JW2 Memory Configuration Jumpers Factory Installed JW2 out when Memory EPROM Ull 32 x 8 256 K JWl out JW2 in when Memory EPROM Ull 64 x Jumpers for Input Output l O Terminal Blocks packages are stocked as in branch parts and are to be installed only by Simplex 512 K Configuration terminal configuration relationships are 1 Pl 2 P2 3 P3 4 P4 7 Figure 9 depicts SW2 as set during manu