Simplex 4090-9101,4090 -9106 IDNet or MAPNET II Zone Adapter Modules (B) (C)

UL ULC CSFM Listed FM Approved NYC Acceptance IDNet or MAPNET II Communicating Devices and 4090 9106 Zone Adapter Modules Peripherals or MAPNET II communications compatible ZAMs Zone Adapter Modules provide an interface to a conventional initiating circuit IDC for Class B or Class A IDCs 4090 9101 Class B Style B monitoring for 2 wire 4 wire initiating devices with power reset for 4 wire devices 4090 9106 Class A Style D monitoring for 2 wire devices Zone device power is supplied separately typically fire alarm control panel Refer to device compatibility list on page 2 use with following Simplex control panels Model Series 4008 4010 and 4100U fire alarm panels for IDNet communications Model Series 4100 4100U 4120 4020 and 2120 Device Transponders CDTs with MAPNET II communications sealed construction Enclosed design minimizes dust infiltration Mounts in standard 4 square electrical box Screw terminals for wiring connections Visible LED flashes to indicate communications Optional covers are available to allow LED to be after installation UL listed to Standard 864 II Monitor ZAMs allow a single point to monitor a conventional initiating circuit IDC populated with 2 wire or 4 wire devices Refer to page two for compatible This product has been approved by the California State Fire Marshal CSFM pursuant to 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in this It is subject to re examination revision and possible cancellation Accepted for City of New York Department of Buildings MEA35 93E Additional listings may be contact your local Simplex product supplier for the latest status Listings and under Simplex Time Recorder Co are the property of Tyco Safety Products IDNet and MAPNET II addressable communications are protected under U S Patent 4,796,025 5,966,002 and 6,034,601 24V IDNET PWR PWR TIME RECORDER CO ZAM CLASS B INSTR 574 183 CODE Series ZAM Package approximately 1 2 size or MAPNET II 1 address per ZAM Input Voltage to 32 VDC nominal 24 VDC Current 24 VDC 16 mA maximum 72 mA maximum current is determined by total requirements ZAM Zone Resistor k cid 58 1 W Connections terminals for in out wiring to 14 AWG wire 0.82 to 2.08 mm2 to 2500 ft 762 m from fire alarm panel or MAPNET II to 10,000 ft 3048 m total wiring including T Taps with Simplex 2081 9044 Protectors H x 4 1 8 W x 1 3 8 D mm x 105 mm x 35 mm Material thermoplastic Plate Material metal galvanized Range to 120 F 0 to 49 C for indoor operation Range to 93 RH at 100 F 38 C 2 2006 Product Selection Modules Number Description Trim Plates Number Description Adapter Module for Class B monitoring of 2 wire or 4 wire initiating devices with power reset for 4 wire devices Adapter Module for Class A monitoring of 2 wire initiating devices semi flush mounted box surface mounted box plate with LED viewing window includes mounting screws steel Resistor Harness Number Reference No Description k cid 58 1 End of Line Resistor Harness for 4090 9101 Class B zone monitoring Monitor ZAM Two Wire Initiating Device Compatibility Reference Chart Number connect photoelectric smoke detector base detector housing with 4098 9601 detector for Existing Equipment heat detectors smoke detectors smoke detector detectors heat detectors Four wire detector operation is compatible with conventional listed contact closure initiating devices Four wire detectors require detector voltage to be connected to resettable power terminals Refer to installation instructions 574 183 and field wiring diagram 842 073 for additional information Contact your local Simplex product supplier for additional compatible devices 2 2006 ZAM Mounting Information setting under label 102 mm square box 2 1 8 mm minimum depth RACO or equal supplied by others ZAM gang blank cover plate and mounting screws for when LED is not required to be externally viewed by others Reference Double Gang Blank Cover Plate mm mm pipe for LED viewing 116 mm 109 mm Trim plate for semi flush mounted box Trim plate for surface mounted box Trim Plates for Visible LED 2 2006 Simplex the Simplex logo MAPNET II and IDNet are trademarks of Tyco International Services AG or its affiliates in the U S and or other countries 2006 Tyco Safety Products Westminster All rights reserved All specifications and other information shown were current as of document revision date and are subject to change without notice Safety Products Westminster Westminster MA 01441 0001 USA 2 2006