Simplex 4090-9106 Monitor ZAM Installation Manual Rev E

Mechanically Installing the Monitor ZAM the Monitor ZAM into a grounded 4 inch UL Listed back box not supplied using Figure 4 as a Mount the ZAM to the back box as follows Loosen the two screws on the square back box Mount the ZAM to the back box using the teardrop holes on the mounting bracket Secure the ZAM to the back box using the two 8 32 panhead screws 9106 Monitor ZAMs Instructions and Warnings NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon unpacking your product inspect the contents of the carton for shipping damage If damage is apparent file a claim with the carrier and notify Simplex HAZARD Disconnect electrical power when making any internal adjustments or repairs should be performed by qualified Simplex Representatives HAZARD Static electricity can damage components Ground yourself before opening or components the procedure below to install the following Monitor Zone Adapter Modules ZAMs Class A Monitor ZAM 4090 9106 Class B Monitor ZAM 4090 9101 which either 2 wire or 4 wire devices Switch Re sealable The LED flashes approximately once every three seconds indicate valid communications with the FACP 1 Monitor ZAM Installation ZAMs are connected to a 4010 Fire Alarm Panel FACP via the IDNet channel ZAMs provide four state status information OPEN CURRENT LIMITED and to the 4010 FACP via the IDNet channel II ZAMs are connected to the 4100 4120 4020 FACP via the MAPNET II channel Monitor ZAMs three state status information NORMAL OPEN ALARM to the host FACP via the MAPNET II ZAM installation consists of the following Setting the Monitor ZAMs address Making electrical connections to the Monitor ZAM Mechanically installing the Monitor ZAM Simplex offers semi flush and surface covers ordered separately with a light pipe The cover s light pipe allow viewing of the communications LED without taking the cover off Installation the 4090 9801 semi flush cover and 4090 9802 surface cover are detailed in publication 4090 Semi Flush Surface Covers and IAM Bracket Installation Instruction 574 796 4 Monitor ZAM Back Box Installation E 2000 Simplex Time Recorder Co Westminster MA 01441 0001 specifications and other information shown were current as of publication and are subject to change without notice is a trademark of Simplex Time Recorder Company II Communication Net is protected by U S Patent 4,796,025 E ON OFF A Monitor ZAM the Monitor ZAMs Address The IDNet channel 4010 FACP only supports address codes 1 through 250 The MAPNET II channel or 4120 or 4020 FACP supports address codes 1 through 127 Monitor ZAM has a unique address The address of the ZAM is set via an eight position DIP switch 1 DIP switch position 1 is the least significant bit LSB and position 8 is the most significant bit Set the ZAMs address using Figure 2 as reference Use a small screwdriver or pen to set the switches device address for the Monitor ZAM should be written on the re sealable label this information provides aid in troubleshooting the system DIP switch in position is while DIP switch in position is IS SHOWN SET AT ADDRESS 7 SWITCHES 5 THRU 8 1000 0100 1100 0010 1010 0110 1110 0001 1001 0101 1101 0011 1011 0111 1111 128 144 160 176 192 208 224 240 129 145 161 177 193 209 225 241 130 146 162 178 194 210 226 242 131 147 163 179 195 211 227 243 116 132 148 164 180 196 212 228 244 117 133 149 165 181 197 213 229 245 118 134 150 166 182 198 214 230 246 119 135 151 167 183 199 215 231 247 120 136 152 168 184 200 216 232 248 121 137 153 169 185 201 217 233 249 122 138 154 170 186 202 218 234 250 123 139 155 171 187 203 219 235 124 140 156 172 188 204 220 236 125 141 157 173 189 205 221 237 126 142 158 174 190 206 222 238 127 143 159 175 191 207 223 239 Electrical Connections to the Monitor ZAM and output signals connect to the Monitor ZAM via the terminals 1 8 as illustrated in 1 Terminal connections for the ZAM are illustrated in Figure 3 Do not loop wire under terminals Break wire runs to provide supervision Notes II IDNet Notes Notes II IDNet Notes Notes II IDNet Notes last next device or to 5 and 6 last device Used Power next device EOL resistor last device next next device EOL resistor last device B Monitor ZAM With 2 Wire Device II supports address codes 1 through 127 only 2 Monitor ZAM Address Chart FACP IDNet Channel the monitor ZAM to the 4010 panel using the 4010 Fire Alarm PC Programmer Installation Programming Instructions 574 187 and 4010 Fire Alarm Front Panel Installing Operating and Instructions 574 052 Refer to 4010 panel label 526 444 for appropriate revision of the to be used FACP MAPNET II Channel the monitor ZAM to the host FACP using the 4100 4120 or 4020 Programmer Report The monitor address and location must match up with the address listed in the specification sheets of the 4100 4120 or Programmer Report B Monitor ZAM With 4 Wire Device When connecting two wires to one terminal position one wire on each side of the terminal screw and MAPNET II lines are 18 AWG twisted pair shield recommended Maximum allowable run from FACP to farthest device not to exceed 2500 feet must be provided from FACP 4009 or regulated Power Limited 24VDC supply that is listed for Fire Protective use Refer to Field Wiring Diagram 842 073 for further information on wiring Monitor ZAMs to IDNet Refer to Field Wiring 841 804 or 841 996 for further information on wiring Monitor ZAMs to MAPNET II IDNet and MAPNET II are supervised and power limited 3 Monitor ZAM Connections