Simplex 4098-9681, -9752, -9753 Duct Housings Installation Instructions

4098 9681 9752 9753 Duct Housings Instructions D DEVICES ARE DUCT SMOKE HOUSINGS WHEN PROVIDED DETECTOR SENSOR THEY ARE DESIGNED TO SAMPLE THE AIR PASSING BY IT IN THE AIR DUCT TO DETERMINE WHETHER IT UNACCEPTABLE LEVELS OF SMOKE EFFECTIVENESS OF A DUCT SMOKE DETECTOR SENSOR IS DEPENDENT UPON THE DESIGN AND OPERATING CONDITIONS OF THE AIR SYSTEM IN WHICH IT IS INSTALLED VARIABLES SUCH AS SMOKE DILUTION AND STRATIFICATION WHICH EVEN THE BEST DESIGNED SYSTEMS HAVE NO AND PROPER PLACEMENT AND POSITIONING OF THE DUCT SMOKE WHICH IS OFTEN COMPROMISED FOR REASONS THE REASONS STATED ABOVE THE EFFECTIVENESS OF THIS SMOKE DETECTOR SENSOR CANNOT BE WARRANTED OR UNDER NO CIRCUMSTANCES SHOULD THIS DUCT DETECTOR SENSOR BE USED AS OR REGARDED TO BE A FOR THE BUILDING REGULAR FIRE ALARM AND SYSTEM TO WHICH THIS DEVICE IS ATTACHED AS A DETECTION DEVICE of Contents of Contents iii Description 1 Duct Housings 4098 9752 or 4098 9753 MAPNET II IDNet 1 the Duct Sensor Address 2 Setting for the 2120 CDT System use with 4098 9752 only 2 Setting for the 4010 4020 4100 or 4120 2 Specifications 5 Duct Housing 5 Duct Housing 5 Duct Housing 4098 9681 9 Routines 14 Installation 14 to Follow 14 Notes 16 Housing Installation 16 Procedures 19 Installation 19 or DC Operation Detector Sensor Testing 21 Differential Pressure Test 22 following an 8 digit Product ID number denotes ULC listed product following an eight digit Product ID number denotes Global product The 2nd suffix identifies market country with this suffix are not UL Listed II Communication Net is protected by U S Patent No 4,796,025 is a trademark of the Simplex Time Recorder Company Analog Detection is protected by U S Patent No 5,155,468 Detector Base is protected by U S Patent No 5,173,683 Simplex Time Recorder Company Gardner MA 01441 0001 U S A Simplex International Time Equipment Co Ltd Mississauga Ontario L4V 1H3 Canada specifications and other information shown were current as of publication and are subject to change without notice PAGE Description Duct Housings or 4098 9753 II IDNet 4098 9681 4098 9752 and 4098 9753 air duct detector sensor housings Figure 1 are designed to sample air and detect smoke in air ducts The and 4098 9753 provide auxiliary contacts for alarm supervisory and functions 4098 9681 duct housing uses the 4098 9601 photoelectric smoke detector 4098 9752 and 4098 9753 addressable duct housing s use the 4098 9714 smoke sensor All housing s must have a baffle installed Use the 4098 baffle furnished with the duct housing 4098 9681 housing has an Red LED and On Green The On LED does not operate for two wire circuits The 4098 and 4098 9753 housing s have a red LED only A pulsating LED On A steady LED indicates an or detailed information on using smoke sensors in air distribution systems see 90A procedures that follow are used to install the 4098 9752 or 4098 9753 duct sensor housings The instructions provided show how to set the at each housing and also how to make electrical connections smoke duct sensors are connected to a 2120 Multiplex Device Transponder 4010 Fire Alarm Panel 4020 Fire Alarm 4100 Fire Alarm Panel or 4120 Fire Alarm Panel by a single twisted wire pair MAPNET II IDNet 1 Duct Housing Assembly the Duct Sensor Address Setting for the 2120 System use with 4098 only sensor addressing is critical since the 2120 Communicating Device CDT 4010 4020 4100 and 4120 Systems report alarms and per duct sensor rather than per zone Each duct sensor has a unique This address is associated with a custom label which identifies its location within a building The duct sensor address and location must up with the address listed in the specification sheets of the 2120 Job Report or Programmer Report for the 4010 4020 4100 or System You should have the appropriate specification sheets with you this part of the installation the 2120 Job Configuration Report find the entry for the duct sensor are about to install The CUSTOM LABEL column provides the while the DEVICE ADDRESS column provides the switch setting the switch setting data for the duct sensor you are installing set the sensor address Locate the DIP switches on the duct sensor base a small screwdriver or pen to set the switches the switch setting data in the DEVICE ADDRESS column is ON while is switch OFF the location of the sensor and its address before electrical example Address M1 7 for the 4010 4100 or 4120 System is in Figure 2 M1 is the addressable channel while 7 is the device on the channel For a duct sensor with Address M1 7 address 7 be set on the duct sensor DIP switches Address 7 is illustrated in 3 Using the example given in Step 1 as a guideline set the duct sensor using Figure 3 Locate the DIP switches on the duct sensor base a small screwdriver or pen to set the switches on next page Setting for the 4010