Simplex 4100+ Alarm Situation Operating Instructions

Simplex AN ALARM SUPERVISORY TROUBLE OPERATING SYSTEMS WITH GLOBAL ACKNOWLEDGE LED IS FLASHING AND TONE ALERT PULSING LED IS FLASHING AND TONE ALERT ON STEADY Pm 0 SUP TABL O ACK rdew TROUBLE FLASHING Unlock and open the panel door The alphanumeric display will the number of alarm conditions 1 0 0 review 0 A Trouble Condition Condition described handled example A a similar manner Unlock and open panel door The alphanumeric display will the number of abnormal conditions Press the ALARM ACK key under the flashing red LED Read alphanumeric display The tone alert display will show pertinent silenced and the alarm LED is ON steady such as shown FLOGR EAST WING STATION 31 ALARM Press ALARM ACK key Read alarm information TO SILENCE THE SIGNALS Press the ALARM SILENCE key and read the display The display will show signal status ALARM SILENCED LED turns ON steady SILENCE PROGRESS TO RESET THE SYSTEM When the alarm condition has been cleared restore or replace affected devices smoke detectors motion sensors etc in with the instructions provided with each device Reset the system FIRE ALARM Condition Press the SYSTEM RESET key PRIORITY 2 ALARM Condition Open the Operator Panel access door and press the Priority 2ALARM key on the programmable CONTROL Key Panel COI Key Panel is located on the far left of the Panel approximately 30 seconds the system will return to normal display the following NORMAL 27 SEP 94 0 z 0 review 1 Press the ACK key under the flashing yellow LED Read and instructions on the alphanumeric display The display the area and type of problem as shown below The tone alert will silenEe and the yellow LED will be ON FLOOR EAST WING MONITOR ZONE CKT TROUBLE Read the alphanumeric display then investigate the problem to cause If a Trouble Condition or replace the defective device wire indicating appliance etc in accordance with instructions The problem will automatically clear when the abnormal has been corrected After a short delay the system will return to normal and the following NORMAL 27 SEP 94 your system switch configuration does not match consult Simplex in the yellow pages specific operations Simplex case of trouble notify 1994 Simplex Recorder Co specifications Manuals Online were current as of publication are subject other change without notice 9 94 AN ALARM SUPERVISORY TROUBLE OPERATING SAFETY AND THE SAFETY OF THOSE AROUND YOU ALWAYS COMES FIRST do know what practices fire depend during SYSTEMS WITH INDIVIDUAL ACKNOWLEDGE ALARM S TROUBLE SILENCEO ON Unlock and open the panel door Read the display It will show number of alarm conditions I 1 0 0 review 0 Press the ALARM ACK key under the flashing red LED Read alphanumeric display The tone alert momentarily silenced and the display will pertinent report information such as shown below FLOOR EAST WING STATION 31 ALARM Press ALARM ACK key Read report data Repeat this When all alarms are acknowledged acknowledge additional alarms alarm LED turns ON steady tone alert silenced TO SILENCE THE SIGNALS Press the ALARM SILENCE key and read the display The display will show signal status ALARM SILENCED LED turns ON steady TO RESET THE SYSTEM When the alarm condition has been cleared restore or replace affected devices smoke detectors motion sensors etc in with the instructions provided with each device Reset the system FIRE ALARM Condition Press the SYSTEM RESET key PRIORITY 2 ALARM Condition Open the Operator Panel access door and press the Priority 2 ALARM key on the programmable CONTROL Key Panel CONTROL Key Panel is located on the far left of the Panel a delay the red alarm LED will flash and the tone alert will sound with a pulsing tone Press the ALARM ACK key under the flashing red LED The display will show the system status Press the ALARM ACK key until all alarm conditions have acknowledged Repeat to acknowledge additional alarms After a delay the system will show the following TROUBLE FLASHING A Trouble Condition Condition described handled example A a similar manner Unlock and open panel door The alphanumeric display will the number of abnormal conditions q 0 0 0 Press the ACK key under the flashing yellow LED Read and instructions on the alphanumeric display The display the area and type of problem as shown below The tone alert will silence momentarily resound FLOOR EAST WING MONITOR ZONE CKT TROUBLE Press the ACK key under the flashing LED again to review the status Read the alphanumeric display then problem to determine cause alphanumeric display will show the area and type of tone alert silenced and the LED turns ON steady If a Trouble Condition or replace the defective device wire indicating appliance etc in accordance with instructions When abnormal condition clears yellow LED will and the tone alert will sound steady Press the ACK key under the flashing yellow LED The display will show the system status Press the ACK key under the yellow LED again After a delay the alphanumeric display should show the NORMAL 27 SEP 94 your system switch configuration consult Simplex in the yellow pages not match specific operations Simplex case of trouble notify 1994 Simplex Time Recorder Co specifications other were current as of publication are subject change wthout notice Manuals Online 9 94