Simplex 4100- and 4120-Series Event and Point Reporting Digital Alarm Communications Transmitters (DACTs) - Installation Instructions

4100 and 4120 Series and Point Reporting Digital Alarm Transmitters DACTs Instructions publication describes the installation procedure for the following Serial Digital Alarm Communications Transmitter SDACT Event Reporting Digital Alarm Communications Transmitter Reporting DACT Point Reporting Digital Alarm Communications Transmitter Reporting DACT Contents Shipment unpacking your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify Simplex Field Wiring Diagrams 841 731 power limited or 841 995 non power limited Fire Alarm System Installation Guide 574 848 this Publication publication discusses the following topics Page Warnings and Regulatory Information to the DACTs Guidelines 1 Connecting to the Phone Lines 2 Configuring the DACT 3 Data and Power Wiring 4 Mounting 5 Testing Table 2001 Simplex Time Recorder Co Westminster MA 01441 0001 USA specifications and other information shown were current as of publication and are subject to change without notice B Warnings and Regulatory Information You May to Provide to Telephone of AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depends upon proper installation HAZARD Disconnect electrical field power when making any internal or repairs Servicing should be performed by qualified Simplex Representatives HAZARD Static electricity can damage components Therefore handle as follows Ground yourself before opening or installing components use the 553 484 Static Control Prior to installation keep components wrapped in anti static material at all times requested by the telephone company the following information must be provided before the DACT to telephone lines Original Manufacturer Simplex Time Recorder Company Model Number 4100 6052 6053 Compliance FCC Part 68 Rules FCC Registration Number 5QWUSA 30334 AL E Type of Jack s to be installed by the telephone company RJ 31X Type of Connector s RJ 45 Ringer Equivalence AC 0.1B DC 1.6 Federal Communications Commission FCC has established specifications that permit this to be directly connected to the telephone network Time Recorder Simplex Drive MA 01441 that the Simplex Model 4100 6052 Event Reporting Digital Alarm Communications and the 4100 6053 Point Reporting Digital Alarm Communications Transmitter to the FCC specifications 15 is subject to the following two conditions This device may not cause harmful electromagnetic interference and This device must accept any interference received including interference that may cause operation 68 equipment complies with FCC Rules Part 68 A label containing the FCC Registration and the Ringer Equivalence Number REN is located on the top of the Fire Alarm Panel bay in which this DACT is installed You must provide this information to the company when requested on next page Warnings and Regulatory Information Continued of REN is used to determine the number of devices that you may legally connect to your lines In most areas the sum of the REN of all devices connected to one line must not five 5.0 You should contact your telephone company to determine the maximum REN your calling area equipment uses the following USOC plug RJ 45 equipment may not be used on party lines or on coin service provided by the telephone FCC compliant telephone cord and modular plug are available for this equipment which is to connect to the telephone network or premises wiring using a Part 68 compliant jack See installation instructions for details the event of equipment malfunction all repair should be performed by Simplex Time Recorder an authorized agent It is the responsibility of users requiring service to report the need for to our Company or to one of our authorized agents Service can be facilitated through our at Time Recorder MA 01441 978 731 2500 to the User user is cautioned that any changes or modifications not expressly approved by the party for compliance could void the user authority to operate the equipment to the DACTs DACTs are option cards that mount within 4100 Fire Alarm Control Panels FACP The 4100 4120 0155 Serial Digital Alarm Communications Transmitter SDACT into 2975 91xx Back Boxes The 4100 6052 Event Reporting Digital Alarm Communications Transmitter Reporting DACT mounts into 2975 91xx Back Boxes The 4100 6053 Point Reporting Digital Alarm Communications Transmitter Reporting DACT mounts into 2975 91xx Back Boxes The 4100 9830 Event Reporting Digital Alarm Communications Transmitter Reporting DACT mounts into 2975 94xx Back Boxes The 4100 9831 Point Reporting Digital Alarm Communications Transmitter Reporting DACT mounts into 2975 94xx Back Boxes 4100 4120 0155 SDACT can be programmed to notify the central station when specified occur or to report changes to a specific point status 4100 6052 9830 Event Reporting DACT notifies the central station when specified events The events are configurable through the 4100 Programmer 4100 6053 9831 Point Reporting DACT reports changes to a specific point status to the station DACTs receive system status messages from the host FACP and communicate the over the public telephone network to a Digital Alarm Communications Receiver at the central station The DACTs are capable of line seizure pulse or tone dialing and monitoring on next page to the DACTs Continued 1 is an illustration of the DACT All DACTs discussed in this publication are identical in TERMINALS RJ 31X JACK JACK PER 4 ADDRESS SW4 TROUBLE LED3 TROUBLE LED2 LED SW3 SWITCH PC P4 COMM P1 CONNECTOR CONNECTOR COMM SW1 1 The Event Reporting and Point Reporting DACTs to the DACTs Continued to Table 1 for DACT LED indicators 1 LED Indications States LED 1 LED LED 2 LED LED 3 LED Illuminated The system is not receiving DC power or the self test failed Steady The DACT is receiving DC power and is DACT is dialing up or attempting to dial up the station Illuminated No communication errors are being detected Steady DACT cannot communicate with the Central All dialing attempts have failed Flashes DACT detects a line fault on phone line 1 Flashes DACT detects a line fault on phone line 2 Flashes DACT detects line faults on both phone when LED alternates between single and double flashes Illuminated DACT is communicating with the host panel Steady DACT cannot communicate with the host panel Flashes There is a version mismatch between the host and the DACT Specifications Specifications VDC Power Supply 2 V max ripple 24 VDC nominal mode 30 mA maximum from the 24 V supply mode 40 mA maximum from the 24 V supply mode 45 mA maximum from the 24 V supply resistance between logic 0 and earth ground must exceed Megohm to 120 F 0 to 49 C to 93 relative humidity at 90 F 32 C