Simplex 4100+ Fire Alarm System Contractor Installation Instructions

4100 Fire Alarm System Instructions 1995 Simplex Time Recorder Co specifications and other information shown were current as of publication and are subject to change without notice 1 95 INSTALLERS OF SIMPLEX 4100 FIRE ALARM PANELS READING THE THIS CALL YOUR LOCAL SIMPLEX REPRESENTATIVE PROCEEDING TO CONNECT FIELD WIRING CONTAINED NOT APPLY AC OR BATTERY POWER TO THE SYSTEM UNLESS IN THE PRESENCE OF A TECHNICAL REPRESENTATIVE POWER LIMITED SYSTEMS CAREFULLY ROUTE FIELD TO PREVENT CONTACT BETWEEN POWER LIMITED AND CONDUCTORS THE AREA IN THE RIGHT BOTTOM OF THE PANEL IS RESERVED FOR NON POWER WIRING ONLY REFER TO THE APPENDIX AND 574 020 FOR MORE INFORMATION OF CONTENTS 1 Documentation 1 Procedure 2 the Delivered Equipment 2 the Back Box 3 and Tag All System Wiring 3 the Peripheral Devices and E O L Resistors 4 the Option Bay Door 6 and Terminate All Zone ZN and Signal SIG Wiring 7 and Terminate All Remaining Circuits 9 the Panel Wiring 9 the Option Bay Door 9 Your Local Simplex Branch Office 9 Power Limited System Wiring Precautions 10 Hardware Envelope Label 2 POINT SUMMARY Report 3 of DIP Switches on Typical Device 4 Address Label 4 the Option Bay Door 6 SUMMARY BY LOCATION Report 7 Custom Terminal Wiring Identifiers 9 Precautions 10 II Addresses 5 Zone and Signal Circuit Meter Readings 8 INSTALLATION INSTRUCTIONS IMPORTANT INSTALLER IS RESPONSIBLE FOR SAFEGUARDING ALL 4100 MATERIAL SHIPPED TO THE SITE SYSTEM INSTALLATION STORE ALL 4100 ITEMS INCLUDING ALL DOCUMENTATION IN CLEAN DRY AND SAFE PLACE UNTIL NEEDED APPROPRIATE PERSONNEL BUILDING OCCUPANTS FIRE DEPARTMENT MONITORING ETC IF AN EXISTING SYSTEM MUST BE SHUT DOWN WHILE THE 4100 SYSTEM IS INSTALLED publication provides a logical sequence of procedures to follow when installing a 4100 system Throughout publication you are often referred to the documentation listed below In such cases notes describing use of the will generally follow immediately after the reference Documentation envelope that contained this publication also contains the following documents 4100 4120 UT Back Box Installation Instructions Pub No 574 020 Factory Documentation packed in a clear plastic envelope 4100 Field Wiring Diagram 841 731 Field Wiring Diagrams Smoke Detectors 841 687 Field Wiring Diagrams MAPNET II Devices 841 804 4100 4100 Fire Alarm Operating Instructions Pub No 574 018 for the last publication all of the above documents are required for system installation If you are unfamiliar with fire alarm system wiring a publication entitled How to Wire a Building for a Fire System Pub No FA2 91 001 can be ordered from Simplex PROCEDURE Indexes for the 4100 Field Wiring Diagram are found on the first page of the document All wiring must be in accordance with local codes A page entitled WIRING PRECAUTIONS is included in the 4100 Field Wiring Diagram possible proceed through the installation process in the sequence that follows the delivered equipment contractor IS NOT responsible for inventorying or installing daughter cards or for interconnecting panel IMPORTANT All cartons that contain daughter cards are to be opened inventoried and installed by Simplex personnel In addition to the envelope that contained this publication and the material listed in the Packaging Information of the Factory Documentation supplied material includes an envelope labeled System Hardware as in Figure 1 CAREFULLY TIME RECORDER CO MA 01441 U S A 1 Hardware Envelope Label the back box Use the 4100 4120 UT Back Box Installation Instructions Pub No 574 020 Note the restrictions for Wiring if applicable and tag all system wiring See the SYSTEM POINT SUMMARY Report Figure 2 and the appropriate page in the 4100 Field Wiring The SYSTEM POINT SUMMARY Report is found within the computer printout portion of the Factory 841 731 4 rev 1 THU 02 JUL 92 H S SUMMARY Point Summary ascending by zone name POINT SUMMARY Name Custom Label ROOM 1 SUPPLY ROOM FURNACE ROOM STORAGE SPRINKLER FIRE PUMP SPRINKLER TAMPER GIRLS LOCKERROOM WING WING LOCKERROOM LOCKERROOM WING AIR INTAKE FAN WING INTAKE FAN AIR EXHAUST WING AIR EXHAUST AIR INTAKE FAN WING INTAKE FAN AIR EXHAUST WING AIR EXHAUST WING ROOM 12 WING WING ROOM 14 WING SUPPLY ROOM SUPPLY MONITOR 2 POINT SUMMARY Report Custom label information tells you where the circuit goes At both ends of each circuit tag wires with zone name and polarity in cases where polarity applies For example SIG 3 and SIG 3 T tapping is permitted only for Style 4 formerly Class B MAPNET II cir