Simplex 4100 Series -9901 to -9926 Retrofit kits for installing 4100ES equipment into existing 2120, 2001, and 4100 Series backboxes

Fire Control Panels ULC CSFM Listed FM Approved Retrofit Kits for Installing 4100ES Equipment into Existing Series Fire Alarm Control Panel Boxes NYC Acceptance existing Simplex 2120 2001 or 4100 fire alarm control panel equipment with Series products using the existing Retrofit kits include either a solid or glass door panels for glass door applications and box hardware Kits are available for 1 2 or 3 bay 4100ES equipment Colors are available to coordinate with existing beige or black boxes or to convert to red or beige the retrofit kits in place standard 4100ES can be easily installed Existing cabinets accommodate internal battery up to 33 Ah ref battery 2081 9276 Ah or higher battery sizes require external cabinets Established 4100ES module placement rules apply existing backboxes include Solid or louvered boxes in 2 Unit 4 Unit or 6 Unit also known as No 2 No 4 or No 6 boxes boxes that are 6 1 2 deep used for 2001 equipment and early 2120 Series equipment boxes that are 6 3 4 deep used for 4100 and for later versions of 2120 Series equipment Listed to Standard 864 Design Reference When the 4100ES Series Simplex fire alarm control panel products was the cabinet dimensions were optimized to newer generations of equipment design 4100ES are narrower taller and deeper than those of the 2001 and 4100 Series products When existing fire alarm control systems capacity or performance increases it is an to consider new product solutions When existing Simplex 2120 2001 4100 Series to 4100ES equipment these retrofit kits allow update to use the existing backboxes Retaining the boxes allows mechanical and electrical impact to reduced often significantly This product has been approved by the California State Fire Marshal CSFM pursuant to 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in this It is subject to re examination revision and possible cancellation This product not approved by MEA NYC as of document revision date Additional listings may be contact your local Simplex product supplier for the latest status Listings and under Simplex Time Recorder Co are the property of Tyco Safety Products Beige retrofit kits are a slightly different color from that of the existing beige boxes Red and are similar but may not exactly match the existing box Consider painting the existing box if color coordination is a concern Application 4 Unit 2120 Backbox with Two Bay 4100ES Continued Applications Examples for these retrofit kits backboxes installed on surfaces that would be to modify such as marble plaster or concrete or installed into a custom enclosure Whether surface or semi flush mounted these retrofit kits can the equipment retrofit process Applications Compatible boxes may be for retrofit from other applications such as some Series Multiplex equipment To determine whether existing box is compatible with these retrofit kits refer box dimension information on page 2 Size Reference 4100ES fire alarm control panel typically mounts in new 2 or 3 bay 4100ES Some 4100ES equipment combinations are for mounting in a single bay size Retrofit kits available to convert the 2120 2001 4100 2 Unit No 2 to accommodate 4100ES single bay equipment Selection Reminder Proper retrofitting existing equipment requires that the desired fire alarm be understood in order to specify the necessary equipment 2120 2001 4100 4 Unit Equipment BoxStandard 4100U two bay box outline4100ES Equipment mounts with two bay Retrofit Kit sized to fit existing boxExisting equipment is removed Solid door 2120 4100 Transponder shown for reference firealarmresources com and 4100ES Equipment Compatibility BMUX The Head End of a 2120 Multiplex System called the BMUX It communicates with a variety of compatible transponders that perform the majority the fire alarm functions 4100ES equipment can be with a dual RS 232 Module 4100 9038 that is for one channel to communicate to a 2120 as a 2120 Transponder Existing Backbox Size Identification Designation Height No 2 527 mm No 4 921 mm No 6 1324 mm diagram below for additional dimension reference Existing Backbox Identification Reference Dimensions 4100ES Equipment Communications a 2120 BMUX is available with 4100ES Series Fire Control Panels MINIPLEX Transponders and Display Units NDUs as Head End For applications where the Fire Alarm Control panel is required to become Head End control existing equipment will be required be replace or upgraded to be 4100ES compatible Width Box Depth Box Depth mm mm mm deep 171 mm 5 8 16 mm Deep box dimensions typical of newer 2120 Style and 4100 Style1 2 13 mm NOTE Conditions of the existing enclosure may require enlarging some of the mounting holes to facilitate kit installationNOTE If holes indicated are not present at each corner drilling will be required details are provided with Installation Instructions 579 766 6 1 2 deep 165 mm 1 3 4 44 mm Shallow box dimensions typical of 2001 Style and older 2120 Style1 3 4 44 mm firealarmresources com 2120 and 2001 Style Shallow Backbox Retrofit Kit Selection for existing 2120 or 2001 Style boxes with box depth 6 1 2 165 mm and with front top lip 1 3 4 44 mm Kit Information Backbox Model Size Reference Reference bay bay bay Series Series Series Series louvered Series Series louvered Series Series louvered Series Series louvered bay Series bay bay Series Series louvered Series Series louvered bay Series bay bay bay bay bay Series Series louvered Series Series louvered Series Series Series Series louvered Series Series louvered Series Series louvered Series Series louvered bay Series bay bay Series Series louvered Series Series louvered bay Series bay bay Series Series louvered Series Series louvered The terms 2 Unit 4 Unit and 6 Unit are used interchangeably with No 2 No 4 and No 6 For semi flush trim kits use 2975 9801 Beige and 2975 9802 Red 2120