Simplex 4902-9210, 4902-9211 SmartSync 2-Wire Operation, Non-Addressable Electronic Chime (F)

cUL CSFM Listed FM Approved Notification Appliances SmartSync 2 Wire Operation Electronic Chime current 24 VDC Simplex SmartSync electronic chime provide Private mode chime tone for applications requiring notification of trained personnel Rugged high impact flame retardant thermoplastic available in red with white lettering white with red lettering Diode polarized input for connection to reverse supervised SmartSync control Notification Circuits NACs two wire control of audible and notification appliance provides SmartSync control of chime tone as Temporal Pattern Time pattern at 60 BPM or on continuously 60 BPM controlled separately from visible on the same circuit Visible appliances on the same circuit operate at a 1 Hz flash rate Refer to page 2 for SmartSync control list and operation information notification appliance design provides easy and convenient semi flush or wall mounting Easily mounts to single gang double gang or 4 inch electrical box wiring terminals 18 AWG to 12 AWG Rear of housing does not extend into box Accessories Mounting adapters to cover surface mounted electrical and to adapt to Simplex 2975 9145 boxes UL listed wire guard 4905 9961 Covers are available separately to change color or for Listed to UL 464 for private mode applications Listed to CSA standards for general signaling use in non fire alarm applications Refer to page 2 for guard listing This product has been approved by the California State Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety See CSFM Listing 7135 0026 334 for allowable values and or conditions material presented in this document It is subject to re examination revision possible cancellation Additional listings may be applicable contact your local product supplier for the latest status Listings and approvals under Simplex Time Co are the property of Tyco Safety Products Westminster SmartSync two wire horn strobe operation is protected under U S Patent No 6,281,789 Chimes are Available as White with Lettering or Red with White Lettering non addressable chimes are private audible notification appliances for applications notification of trained personnel instead of the public Typical applications would be in medical areas where the softer chime tones are less than conventional fire alarm audible two wire advantage When selected for mode these chimes follow control signals on the same two wire NAC circuit as fire alarm Using a two wire control can significantly reduce time and expense for both retrofit and new mounting Chimes can be semi flush or mounted on a standard single gang double gang 4 square 102 mm electrical box Optional are available to increase mounting and flexibility 4 2010 SmartSync Two Wire Control operation mode allows a two wire circuit to the ability to activate both the chime and strobe the same NAC and then allow the chime to be silenced the strobe remains flashing The chime operates as while the strobe operation is SmartSync Control Sources two wire control is available from 4008 4100U and 4010 Fire Alarm Control refer to individual product data sheets for more IDNet NAC Extenders refer to data sheet SmartSync Control Module SCM Model 4905 9938 to data sheet S4905 0003 Product Selection White non addressable electronic H x 5 W x 1 1 2 D mm x 127 mm x 38 mm to cover 1 1 2 deep mounted boxes H x 5 1 4 W x 1 5 8 D mm x 133 mm x 41 mm depth with chime 3 1 8 79 mm mount red adapter skirt mount white adapter skirt Adapter Plate red for mounting to Simplex 2975 9145 box for retrofit may be mounted vertical or horizontal Red mounting box requires Adapter Plate 4905 9931 Control Module SmartSync Control Module Class A or Class B installs in 4 box and Guard Red chime cover with white lettering White chime cover with red lettering Wire guard with mounting plate red compatible with semi flush surface mounted boxes UL listed by Space Age Electronics Inc x 5 3 4 x 0.060 thick mm x 146 mm x 1.5 mm x 5 1 8 x 2 3 4 D mm x 130 mm x 70 mm x 4 1 8 x 1 1 4 D mm x 105 mm x 32 mm H x 5 W x 1 1 2 D mm x 127 mm x 38 mm H x 6 1 16 W x 3 1 8 D mm x 154 mm x 79 mm 4 2010 TrueAlert Non Addressable Chime Specifications Voltage Range Current Sound Output Characteristics Output Ratings per UL 464 Chamber test 10 ft 3 m Range Range dBA VDC to 33 VDC mA is adjustable from 750 Hz to 1300 Hz factory setting is approximately 800 Hz output is adjustable from 34 dBA to 63 dBA factory setting is 63 dBA to 122 F 0 to 50 C to 93 non condensing 100 F 38 C blocks for 18 AWG to 12 AWG 0.82 mm2 to 3.31 mm2 two wires per for in out wiring Factory settings are recommended for most applications Always test installed sound level against local requirements Installation Reference additional information refer to Installation Instructions 579 868 or Semi Flush Chime Mounting is compatible with gang double gang and 102 mm square boxes 38 mm deep by others View of Chime with Surface Adapter Skirt mount conduit and shown for reference square box profile 38 mm deep NAC wiring test points are with cover removed terminals are from rear Guard cover required mount adapter skirt Red 4905 9940 White knockouts on all four sides 4 2010 Holes gang 2 gang 4 square 4 4905 9931 Adapter Plate Installation Information Adapter Plate Box Adapter Plate Optional Wire Guard here for reference only can be used on other mounting options is a registered trademark of Tyco International Services GmbH and is used under license Simplex the Simplex logo IDNet TrueAlert and SmartSync are trademarks of International Ltd and its affiliates and are used under license 2010 Tyco Safety Products Westminster All rights reserved All specifications and other information shown were current as of document revision date and are subject to change without notice Safety Products Westminster Westminster MA 01441 0001 USA 4 2010