Simplex Addressable Initiation Peripherals; IDNet and MAPNET II Communicating Devices; Model 4090-9008 Dual Contact Relay IAM; 4090-0014

ULC CSFM Listed Approved Initiation Peripherals IDNet and MAPNET II Communicating Devices 4090 9008 Dual Contact Relay IAM Contact Relay IAM Individual Addressable A single addressable point provides control and status of two 2 A Form contacts Low power latching relay design allows IDNet or II communications to supply both data and power Relay is set to OFF on initial power up and upon loss of or MAPNET II communications use with following Simplex control panels Model Series 4007ES 4010ES 4100ES and 4100U fire control panels for IDNet communications Model Series 4100 4100U 4100ES 4120 4020 and Communicating Device Transponders CDTs with MAPNET II communications construction Mounts in standard 4 102 mm square electrical box adapter bracket is available to mount in a 11 square electrical box Screw terminals for wiring connections Visible LED flashes to indicate communications can be at panel to indicate activated state Optional 4 square box covers are available to allow to be viewed after installation listed to Standard 864 Dual Contact Relay IAMs allow fire alarm control to control two remotely located Form contact IDNet or MAPNET II addressable communications both data and module power Typical applications be for switching local power for control functions as elevator capture or control of HVAC components fans dampers etc Relay status is also requiring only one device address Selection Dual Contact Relay IAM Adapter Plates Adapter plate to fit 4 11 119 mm square box For semi flush trim plate for 4 box with LED viewing includes mounting For surface galvanized steel box This product has been approved by the California State Fire Marshal CSFM pursuant to 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in document Additional listings may be applicable contact your local Simplex product for the latest status Listings and approvals under Simplex Time Recorder Co are property of Tyco Fire Protection Products Dual Contact Relay IAM approximately 1 2 size or MAPNET II communications address per device by communications 3.12.04 or higher Firmware Ratings not rated for incandescent switching Form C contacts DPDT with block access to Common and N C for each contact A 30 VDC resistive A 30 VDC inductive listed alarm 0.5 A 125 VAC resistive Fusing contact common is fused with a A fast acting non time delay fuse Provide external transient suppression as required per DC inductive loads can typically be diode 120 VAC loads may require RC networks or depending on device type Refer to Installation Instructions for additional information Connections Screw terminals for in out wiring to 14 AWG wire 0.82 to 2.08 mm2 to 2500 ft 762 m from control to 10,000 ft 3048 m total wiring including T Taps with Simplex 2081 9044 Protectors H x 4 W x 1 D mm x 102 mm x 35 mm metal galvanized to 120 F 0 to 49 C for indoor operation to 93 RH at 100 F 38 C Plate Range or II Reference 11 2014 Dual Contact Relay IAM Mounting Information 102 mm square electrical 2 1 8 54 mm minimum supplied separately 119 mm square electrical 2 1 8 54 mm minimum depth separately or 4 square cover supplied separately mounting screws with box Dual Contact IAM Assembly Adapter Plate for square box includes 8 mounting screws Reference with 4 11 16 Square and 4 Square Boxes mm mm supplied label cover on site if 120 VAC pipe for LED viewing 116 mm Trim plate for mounted box 109 mm Trim plate for mounted box Trim Plates for 4 Square Boxes with Visible LED SIMPLEX and the product names listed in this material are marks and or registered marks Unauthorized use is strictly prohibited 2014 Tyco Fire Protection Products All rights reserved All specifications and other information shown were current as of document revision date and are subject to change without notice Fire Protection Products Westminster MA 01441 0001 USA 11 2014