Simplex Autocall Optical Beam Smoke Detector

OPTICAL BEAM SMOKE DETECTOR cid 2 cid 4 cid 3 cid 31 cid 11 cid 22 cid 18 cid 9 cid 7 cid 4 cid 6 cid 5 cid 4 cid 18 cid 9 cid 8 cid 3 cid 9 cid 10 cid 2 cid 11 cid 12 cid 12 cid 11 cid 1 cid 2 cid 2 cid 4 cid 11 cid 13 cid 14 cid 15 cid 21 cid 6 cid 2 cid 3 cid 11 cid 22 cid 18 cid 23 cid 2 cid 6 cid 3 cid 10 cid 2 cid 11 cid 5 cid 24 cid 11 cid 4 cid 18 cid 29 cid 2 cid 31 cid 2 cid 4 cid 3 cid 31 cid 2 cid 11 cid 29 cid 2 cid 9 cid 7 cid 4 cid 23 cid 4 cid 29 cid 2 cid 31 cid 22 cid 2 cid 3 cid 9 cid 5 cid 3 cid 31 cid 11 cid 18 cid 6 cid 11 cid 21 cid 5 cid 4 cid 18 cid 16 cid 3 cid 4 cid 29 cid 5 cid 4 cid 3 cid 31 cid 2 cid 11 cid 18 cid 6 cid 11 cid 18 cid 4 cid 1 cid 6 cid 2 cid 3 cid 5 cid 31 cid 4 cid 11 cid 9 cid 4 cid 2 cid 6 cid 3 cid 2 cid 11 cid 4 cid 18 cid 18 1 cid 11 cid 22 cid 5 cid 6 cid 6 cid 2 cid 9 cid 4 cid 1 cid 31 cid 2 2 cid 31 cid 2 cid 11 cid 29 cid 7 cid 4 cid 2 cid 16 4 cid 6 cid 7 cid 16 cid 11 cid 8 cid 2 cid 31 cid 2 cid 4 cid 18 cid 6 cid 3 cid 31 cid 3 cid 4 cid 18 cid 9 cid 7 FIRERAY 2000 optical smoke detector is an ac infrared smoke detector of three base ele a transmitter receiver control unit Analysis of the infrared beam by control unit determines smoke is present and so generates an alarm sig FIRERAY 2000 with transmitter and re is ideal for use in aes designed areas or ornate and historic ceil make the use of point type impractical 2000 Optical Beam Smoke Detector FIRERAY 2000 optical beam smoke is specifically designed for use in open type interiors such as warehouses plants aircraft hangars and where the installation and servic of point type detectors may be difficult or Other common areas where detectors are used include power hotel lobbies shopping malls galleries cathedrals and churches beam type fire detector projects a infrared light beam from the trans to the receiver unit The received signal analyzed and in the event of smoke being for a predetermined period of time alarm condition is activated single FIRERAY 2000 beam can cover a open area of up to 328 feet 100m in and up to 45 feet 14m wide giving an protection area of up to 14,760 feet 1,400sq m Detection When smoke is present the beam the signal received is reduced to level determined by the density of the In the event of the smoke reducing the strength between the specified alarm and 93 obscuration for a period 5 10 seconds the fire alarm output is Three alarm thresholds can be se 25 1.25dB 35 1.87dB or 50 3.0dB Reset Approximately 5 seconds after fault condition is indicated the receiver au resets if the fault is no longer Gain Control AGC Long term of signal strength by component or build up of dirt on optical surfaces not generate an alarm because of com provided by the AGC circuit This by comparing the received signal a standard at predetermined time Differences of more than 7 are by the automatic selection of gain Indication In the event of a power at the transmitter or if the signal is by more than 93 for a period in of 5 seconds then the fault alarm is This condition inhibits the fire until the signal is restored The align lamp on the receiver door flashes the condition prism reflector unit is available for use in when the distance between the and transmitter is less than 33 feet The prism can also be used to reduce costs by installing the transmitter receiver together and reflecting the from the far side of the protected area UL Listed File Number S3417 CSFM No 7260 1508 101 1 of 2 BEAM SMOKE DETECTOR Beam note 1 ft Beam max and over 29 32 25 25 approx approx 11 32 13 32 ceiling or roof with a slope in excess of 3.5 should be regarded as an apex roof 13 16 15 64 FIRERAYS are mounted in the apex the horizontal distance may increase by 1 each degree of ceiling slope up to 25 maximum for FIRERAY in apex only Ceilings Sloping Roof Ceilings Sloping Roof note 1 Unit Dimensions 25 25 max 50 25 12.5 approx Dimensions Use and transmitter should be positioned approx 19 inches below the ceiling 1 No more than 10 feet approx of the beam path should be within 19 inches approx of any wall or partition Solid lines show beam from transmitter Dashed lines show secondary reflection which not intersect with the receiver due to wall Dotted lines show main part of reflected beam back to the transmitter receiver is a trademark of Tyco International Services AG or its affiliates in the US and or other countries Temperature Range Current Current Range Alarm Thresholds to 131 20 to 55 VDC to 28 VDC mA mA to 328 feet to 100 meters 25 35 50 RAL 9010 Unit 15 64 H x 8 17 64 W x 3 11 32 D H x 210mm W x 85mm D 3 4 H x 3 5 32 W x 4 17 32 D H x 80mm W x 115mm D 2000 Optical beam smoke detector includes transmitter receiver Information control unit reflector unit tool 2 of 2