Simplex BMUX Operating

SSimplex be pertonned qualified Simplex Representa this system controlled programming reprogram result sig the system BMUX comply with the limits and can radiate used may cause has been a Class A of Part 15 of provide Subpart 11 not pursuant equipment and found Rules which are designed be required a residential which case such correct interference operated cause user at his own expense lake whatever measures may be Before attempting publication Of particular actions required durinq alarm conditions operate or program read this are the instructions on pages 4 and 5 which 2120 BMUX it is important OF 2120 BMUX BMUX Processing Unit the 2120 Multiplex System sometimes as Multiplex the central operating unit when buildings a number of 2120 monitors selected conditions When an initiating device activates describes turn responds by reporting system Each customer location of a zone a building or the BMUX The the operator and operation of preselected system when KEYBOARD shown panel an optional keyboard and an optional Figure 1 the BMUX contains an operator 1966 Simplex Recorder Gardner Mass 01441 0001 1 CONTROL PANEL AND LOCAL PRINTER FEATURES to Figure 2 LOCATION status is being reported not supplied DISPLAY Alphanumeric LED display shows system conditions and location data Figure 3 shows a typical When pressed display indicates LOC THIS PNT is displayed when customer the point SIGNAL SILENCE pushbutton When pressed alarm signaling devices are silenced NOTE This pushbut does not silence the BMUX tone device DETECTOR RESET pushbutton When pressed following alarm conditions certain peripheral devices are to NORMAL supervisory conditions and control functions are returned to their pre alarm states when system is in normal condition no trouble no alarm ALL CLEAR LED LAMP TEST pushbutton PRIORITY 1 ALARM LED Flashes to indicate change in state of highest priority alarm condition On steady When pressed all LEDs including display and tone device are tested condition acknowledged Off when condition normal PRIORITY 2 ALARM LED Flashes indicate change state of second highest alarm condition steady when condition acknowledged Off when condition normal TROUBLE LED Flashes indicate change state of trouble condition On steady when condition ac Off when condition normal ACKNOWLEDGE acknowl This pushbutton may be used to sequentially display Priority 1 alarms when the associated LED is steady Priority 1 alarms When pressed Priority 1 alarm condition ACKNOWLEDGE acknowl This pushbutton may be used to sequentially display Priority 2 alarms when the associated LED is steady Priority 2 alarms When pressed Priority 2 alarm condition ACKNOWLEDGE Trouble conditions When pressed Trouble condition acknowledged sequentially display Trouble conditions when associated LED is on pushbutton may be used EXAMINE pushbutton Priority 3 monitor points When repeatedly pressed activated Priority 3 monitor are sequentially displayed EXAMINE pushbutton displayed activated control points When repeatedly pressed activated control points are LOCAL PRINTER Prints major events time and location as the event occurs PAPER PRINTOUT System conditions are reported by the local printer as they change 3 a sample printout ADVANCE pushbutton REWIND pushbutton When pressed pressing local printer paper is advanced the local printer paper pulled out from the top take up roll to examine button will cause the paper to be rewound onto the take up roll to remove any RESET TEST POlNTS ACTIVATED PRINTOUT CODE USED or Point Number Position Number Number Number ALARM CLEAR ACKNOWLEDGE TROUBLE ABNORMAL 2 3 Condition ALL CLEAR lamp 5 is on Display 1 shows time date and day Display is blank when no keyboard Condition LEDs 7,8 and 9 are off installed or Trouble Condition BMUX tone device sounds One or more condition LEDs 7 8 and 9 are flashing ALL CLEAR LED 5 is off Display 1 shows type of alarm or trouble Printout 15A from local printer 15 reports status change on three lines code and condition Line Type of alarm or trouble Line Time date and day Line Location Figure 3 for sample printout code and condition custom labels are supplied To Do During Alarm or Trouble Condition 1 Press ACKNOWLEDGE 12 adjacent flashing LED there is only one status change condition Display 1 and printout 15A will show condition acknowledged BMUX tone device is silenced Condition LED 7 8 or 9 is on steady If more than one status change condition Display and printout will show condition pressed BMUX device silenced only when all conditions have been acknowledged NOTE the SIGNAL SILENCE pushbutton 3 will not silence the BMUX tone device Condition LEDs 7 8 and or 9 will change flashing steady only when all have been acknowledged 2 Press LOCATION to show location of the status change on the display 1 If multiple status change conditions have occurred acknowledged will be displayed change condition needed location information on the last on a particular Repeatedly press the appropriate ACKNOWLEDGE pushbutton 10 ll or 12 until selected condition displayed then Press the LOCATION INFORMATION pushbutton 2 3 Take whatever action is required When it is appropriate the alarm or trouble situation do so the audible alarm signaling devices can be silenced This action will be indicated on the pressing the SIGNAL SILENCE pushbutton 1 and the printout 15A Restore The System To Normal 1 Correct the alarm or trou